John Bean JLT4500S Скачать руководство пользователя страница 22

Страница: 22 / 71

REV 02 OCT 2020 JLT4500-IOM-F

17) Connect one end of the Power Unit Hose (EAH0065V28A, L=490) to the installed Bulkhead fitting(EAH0072T09A), another end to the

fitting (EAH0065V20A) on Power unit, see

Fig. 13

Fig. 13, Assemble Hose

18) Assemble Power Side Lock Cover Assembly (EAM0128V03A, SCREW 1-02088A) to power column, see

Fig. 13

Don’t need to install

the screw tightly.

19) Using the Overall Width (C) Dimension from

Table1

Fig. 3

, chalk two parallel lines (within 2mm tolerance) and one CENTER LINE on

the floor. See below

Fig. 14

NOTE: The anchor bolts must be installed at least 200 mm from any crack, edge, or expansion joint.

Fig. 14, Layout the columns

20) Erect or lift Power Column assembly using a mechanical assist such as lift truck or Jeanie Lift.

DANGER

Make sure that while raising the column, the load is always properly held. To install the lift is preferable to use a crane; using a fork

lift is acceptable, but in this case oversized forks shall be installed, positioning them as close as possible to the load

21) Position Power Column on chalk lines from bay layout and confirm rectangle notches are aligning with the CENTER LINE, see

Fig.

14.

22) Drill one anchor hole using the base plate as a template at

(see

Fig. 14

) to a depth of 150mm minimum, but DO NOT drill through

the concrete, see step 1 of

Fig. 15

NOTE: Use a concrete hammer drill with a carbide bit. Tip diameter should conform to

5.3.2. Do not use excessively worn

bits or bits which have been incorrectly sharpened. A core bit may be necessary if an obstruction is encountered. NEVER

substitute with shorter anchor.

EAH0072T09A

EAM0128V03A,
Lock Cover

1-02088A,
M5X8, 4Pcs

EAH0065V28A

Power Side Column Extension

Power Side Column Assembly

Power Unit

EAH0065V20A

Rectangle Notch

Содержание JLT4500S








































































Результаты поиска

Содержание JLT4500S

Отзывы:

Похожие инструкции для JLT4500S

Бренды по названию

Популярные бренды

John Bean JLT4500S, Руководство пользователя

Результаты поиска

Содержание JLT4500S

Отзывы:

Похожие инструкции для JLT4500S

Бренды по названию

Популярные бренды