John Bean JLT4500S Скачать руководство пользователя страница 10

Страница: 10 / 71

REV 02 OCT 2020 JLT4500-IOM-F

4.4 ELECTRIC HAZARD

This hazard is present if the electric connections are not compliant to the applicable safety local norms.

ATTENTION

Before connecting the lift to the electric line, verify that the line itself is completely compliant to the enforced norm.

Also make sure that the electric line can supply the needed power and that:

•

there is a properly working grounding circuit

•

there is a properly working protection circuit

ATTENTION

Before plugging the lift to the main power supply or before any maintenance work, make sure that the main switch of the power

supply is set to the OFF (0) position.

4.5 GENERIC HAZARDS

Any other use or operation not in compliance with this manual could cause damages to the user and or to the lift.

An un-forecasted and unexpected use alters the technical characteristics for which the lift has been designed and manufactured and could

then compromise its correct and safe use.

DANGER

The lift was designed for indoor operation only. Do not install and/or use this lift outdoor.

DANGER

It is absolutely forbidden to raise persons with this lift.

It is forbidden for people to stand on the load or load carrying devices when they are raised.

Содержание JLT4500S








































































Результаты поиска

Содержание JLT4500S

Отзывы:

Похожие инструкции для JLT4500S

Бренды по названию

Популярные бренды

John Bean JLT4500S, Руководство пользователя

Результаты поиска

Содержание JLT4500S

Отзывы:

Похожие инструкции для JLT4500S

Бренды по названию

Популярные бренды