John Bean JLT4500S Скачать руководство пользователя страница 40

Страница: 40 / 71

REV 02 OCT 2020 JLT4500-IOM-F

DANGER

Prior to any kind of maintenance and/or cleaning operation is performed, completely lower the carriages, unload the lift and make

sure that there is no pressure in the hydraulic hoses and disconnect the power source from the lift.

DANGER

For the extraordinary maintenance of the JLT4500 type lift, address exclusively to the qualified JohnBean technical support.

5.6.1 PERIODIC CHECKS:

DANGER

Modifications not authorized in writing by the technical staff of JohnBean could affect the safe use of the lift.

WARNING

The lift was designed considering an expected life of 20000 working cycles. Exceeding this working life could result in fatigue

overload of the structure and could affect the safe use of the lift. Fatigue is an inevitable effect of the use of the lift and should be

taken in proper account. A good maintenance is extremely important not to make the effect of the fatigue on the structure worse than

they actually are.

The following maintenance points are suggested as the basis of a routine maintenance program. The actual maintenance program should be

tailored to the installation.



If lift stops short of full rise or chatters, check fluid level and bleed both cylinders per Installation Instructions.



Replace all Safety, Warning or Caution Labels if missing or damaged

5.6.1.1 DAILY CHECKS:



Keep lift components clean.



Check for loose or broken parts.



Check hydraulic system for fluid leaks.



Check adapters for damage or excessive wear. Replace as required with genuine

JohnBean

parts.



Check the activation of the Lock Release. When properly adjusted, the column lock should rest firmly against the back of the column

when engaged and pull clear of the column back when disengaged

5.6.1.2 WEEKLY CHECKS:



Check synchronizing cables and sheaves for wear. Replace as required with genuine

JohnBean

parts.



Check synchronizing cable tension per Installation Instructions. Adjust if necessary.

ATTENTION

Important: if any of the locks does not fully disengage, damage may result to carriage and or cable synchronizing system.

Содержание JLT4500S








































































Результаты поиска

Содержание JLT4500S

Отзывы:

Похожие инструкции для JLT4500S

Бренды по названию

Популярные бренды

John Bean JLT4500S, Руководство пользователя

Результаты поиска

Содержание JLT4500S

Отзывы:

Похожие инструкции для JLT4500S

Бренды по названию

Популярные бренды