John Bean JLT4500S Скачать руководство пользователя страница 11

Страница: 11 / 71

REV 02 OCT 2020 JLT4500-IOM-F

DANGER

It is not allowed to perform any type of aid and/or maintenance operation to the lift while being operated

DANGER

Before operating the lift, make sure that the vehicle to be lifted does not have any fluid leakages.

If fluids are spilled on the floor immediately remove them.

DANGER

Do not wash the vehicle on the lift.

DANGER

Before operating the lift, visually check all the components of the lift and in particular the safety

devices for possible defects. Do not operate the lift even if any defect is detected.

DANGER

The sound level of the noise generated by the lift is Laeq≤84 dB (A).

4.6 EMERGENCY STOP

In the case an emergency stop is needed, to interrupt the operation of the lift, just release the main switch and it will automatically rotate back

in the “OFF” position, see

Fig. 1

; or press the E-Stop button, see

Fig. 2

. In order to resume the working cycle previously

interrupted, the user shall turn the main switch clockwise into the “ON” position or turn the mushroom head of the E-Stop button clockwise

until it rebound.

Fig. 1, Main switch on the main control
box of Power Side Column

Fig. 2, E-Stop on the remote control

box of Idler Side Column

Содержание JLT4500S








































































Результаты поиска

Содержание JLT4500S

Отзывы:

Похожие инструкции для JLT4500S

Бренды по названию

Популярные бренды

John Bean JLT4500S, Руководство пользователя

Результаты поиска

Содержание JLT4500S

Отзывы:

Похожие инструкции для JLT4500S

Бренды по названию

Популярные бренды