JF FCT King Size 1260 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 114

background image

1. INTRODUCTION

PIGB-206X-02 FCT1460 0614

- 18 -

GRINDING

When grinding always follow this procedure:

- Stop the tractor engine and remove the ignition key.
- Activate the parking brake.
- Wait until all moving parts have stopped.

Unfortunately it is necessary to remove some of the guards to change the direction of
rotation  of  the  rotor  when  grinding  the  blades.  As  there  are  chain  and  belt
transmissions  your  hands  may  be  injured  if  the  revolving  parts  have  not  stopped
before the guards are removed.

Grinding is performed according to the following procedure:

1.  Check  if  the  grindstone  is  undamaged  and  if  the  device  is  able  to  move  back

and forth easily.

2.  Lower the guard behind the grinding device to give access to the blade cylinder.

3.  Adjust the stone and guard the grinding device again.

4.  Remove  the  guard  above  the  blade  cylinder  transmission  and  change  the

direction of rotation of the rotor.

5.  Close the guard again and check that there are no persons near the machine.

6.  Start the tractor again and keep the rpm at idle speed or a little above.

7.  Perform the grinding carefully.

Always use safety glasses when grinding as small particles from the grindstone might
hit you.
When grinding has finished, stop the tractor engine, remove the ignition key, change
the direction of rotation and fasten all guards.

REMEMBER:

Always grind with all guards closed.

«
...
16
17
18
19
20
...
»

Содержание FCT King Size 1260



















































































































Отзывы:

Нет отзывов

Похожие инструкции для FCT King Size 1260

Бренд: Taber Страницы: 27

Бренд: Backyard Discovery Страницы: 51

Бренд: Nautilus Страницы: 12

Бренд: CAIRE Страницы: 16

Бренд: ParaBody Страницы: 3

Бренд: Hach Страницы: 52

Бренд: hager Страницы: 2

Бренд: Tascam Страницы: 8

Бренд: P-Q Controls Страницы: 5

Бренд: P+L Systems Страницы: 2

Smart Plus PHT-35LHS

Бренд: Vatech Страницы: 190

Бренд: Salter Страницы: 18

Бренд: Salter Страницы: 42

Бренд: Salter Страницы: 47

Бренд: Salter Страницы: 35

Бренд: Salter Страницы: 40

M-041 INDOOR CROSS

Бренд: Salter Страницы: 15

Heart Guardian AED

Бренд: Radian Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды