JF FCT King Size 1260 Скачать руководство пользователя страница 71

Страница: 71 / 114

5. METAL DETECTOR (MD)

PIGB-206X-02 FCT1460 0614

- 71 -

ADJUSTMENTS

RATCHET STOP

Fig. 5-8

The stop system of the metal detector is integrated in the transmission for the feed
intake system. The system consists of a pawl

and a ratchet wheel

and is

activated by a coil

. The system is activated when metal is registered in the feed

intake section and the coil gets a signal from the electronics which brings the pawl

in mesh with the ratchet wheel

and the feed intake section is blocked.

Fig. 5-9

WARNING:

The distance between the pawl and the wheel MUST be S= 1-2
mm as the distance determines the reaction time of the system
in case of metal detection.

Too large distance may mean that a metal object can reach the
blade rotor before the feed intake stops and cause serious
damage to the harvester.

The distance between pawl and wheel has been adjusted correctly from the factory.
If it becomes necessary to readjust, it is done by means of the adjusting screw

above the coil

Fig. 5-8

-1

Fig. 5-9

-1

Содержание FCT King Size 1260



















































































































Результаты поиска

Содержание FCT King Size 1260

Отзывы:

Похожие инструкции для FCT King Size 1260

Бренды по названию

Популярные бренды

JF FCT King Size 1260, Инструкция по применению

Результаты поиска

Содержание FCT King Size 1260

Отзывы:

Похожие инструкции для FCT King Size 1260

Бренды по названию

Популярные бренды