JF FCT King Size 1260 Скачать руководство пользователя страница 98 | Manualshive

Страница: 98 / 114

background image

9. STORAGE (WINTER STORAGE)

PIGB-206X-02 FCT1460 0614

- 98 -

9. STORAGE (WINTER STORAGE)

When the season is over, the preparation for winter storage should be made
immediately after. First, clean the machine thoroughly. Dust and dirt absorb moisture
and moisture increases the formation of rust.

CAUTION:

Be careful when cleaning with a high pressure cleaner. Never
spray directly on the bearings and grease all grease points
carefully after cleaning so that possible water is pressed out of
the bearings.

IMPORTANT: Grease all grease points after cleaning the machine.

The following points are instructions how to prepare for winter storage.



Check the machine for wear and other defects

– note down the necessary parts

you will need before the next season and order the spare parts.



Dismount the PTO drive shafts, lubricate the profile tubes and keep them in a
dry place.



Spray the machine with a thin coat of rust-preventing oil. This is especially
important on parts polished.



Change the oil in the gearboxes.



Store the machine in a ventilated building.



Lay up the machine to unload the tyres.

«
...
96
97
98
99
100
...
»

Содержание FCT King Size 1260



















































































































Отзывы:

Нет отзывов

Похожие инструкции для FCT King Size 1260

Бренд: ZOLL Страницы: 344

Бренд: ABB Страницы: 9

Бренд: Landoll Страницы: 6

Бренд: ParaBody Страницы: 9

Бренд: ParaBody Страницы: 3

Бренд: MacDon Страницы: 45

Бренд: H&S Страницы: 30

Бренд: Yamaha Страницы: 50

Бренд: A&D Страницы: 30

Бренд: Raymarine Страницы: 90

Бренд: idiag Страницы: 10

Бренд: Bandit Страницы: 136

Versaflo S Series

Бренд: 3M Страницы: 11

DBI Sala EXOFIT

Бренд: 3M Страницы: 32

Бренд: 3M Страницы: 8

Бренд: Accurate Bio-Medical Technology Страницы: 35

Бренд: ACCU-CHECK Страницы: 104

Бренд: Federal Страницы: 43

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды