JF FCT King Size 1260 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 114

background image

1. INTRODUCTION

PIGB-206X-02 FCT1460 0614

- 17 -

WORKING

Before you start working make sure that no persons are behind the forage harvester
due to the danger of being hit by metal parts from damaged blades.

Also make sure that there are no persons in the trailer used for picking up. There is
danger of suffocating in the flow of material or getting hit by metal parts.

If the feed rollers or the blade cylinder are blocked, disengage the clutches and stop
the tractor engine immediately. Activate the parking brake and wait until the revolving
parts have stopped before removing the material or the foreign matter.

WARNING:

This cannot be said often enough: Never remove material blocked in
the machine while the machine is running and never feed material
into the pick-up with your hands or feet as there is a serious danger
of getting caught and pulled into the harvester which would cause
dismemberment or death.

Never allow anyone to stand near the forage harvester while it is working, especially
not children who do not know the danger and do unforeseen things.

The chute is over 4 m high. Be aware of high-voltage lines and keep a safe distance
away from these.

PARKING

Before parking the machine always lock the jack with the locking pin, otherwise the
machine may tip over during parking. Also remember to block the wheels if there is a
risk that the machine will move after parking

Remember to remove the hydraulic hoses and the control box before driving away
with the tractor.

GREASING

When greasing or maintaining the machine never let more than one person work at
the  machine  at  a  time.  This  reduces  the  risk  of  getting  fingers  caught  because
another person by accident turns the revolving parts while you are still working with
them.

Never  try  to  clean,  grease  or  adjust  the  machine  before  the  PTO  has  been
disengaged,  the  tractor  engine  has  stopped  and  the  parking  brake  been  activated.
Remove the ignition key and wait until all moving parts have stopped!

«
...
15
16
17
18
19
...
»

Содержание FCT King Size 1260



















































































































Отзывы:

Нет отзывов

Похожие инструкции для FCT King Size 1260

Бренд: UNIS Страницы: 16

Bathomatic Basic

Бренд: Unique Automation Страницы: 10

Бренд: Additel Страницы: 139

Бренд: X-METAL Страницы: 135

TR 2B INC INT NC

Бренд: OMGA Страницы: 76

SimNewB Anomaly Set

Бренд: laerdal Страницы: 10

Бренд: Honestech Страницы: 43

Бренд: Focal Meditech Страницы: 10

Бренд: Rohm Страницы: 17

Бренд: Joyolight Страницы: 4

SynCore RW Unit

Бренд: Ridder Страницы: 28

Бренд: Godox Страницы: 8

Scanmate-B DGH 8000

Бренд: DGH TECHNOLOGY Страницы: 53

Бренд: Monosem Страницы: 104

Бренд: Stahls Страницы: 2

Porta PlumeSafe 604

Бренд: Buffalo filter Страницы: 75

Бренд: Hettich Страницы: 104

Shark Beam FX one

Бренд: SHOWTEC Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды