JF FCT King Size 1260 Скачать руководство пользователя страница 73 | Manualshive

Страница: 73 / 114

background image

6. WORKING IN THE FIELD

PIGB-206X-02 FCT1460 0614

- 73 -

6. WORKING IN THE FIELD

GENERAL CONDITIONS

Adjust  the  machine  to  the  maximum  cutting  length  acceptable  for  the  crop  in
question. This will reduce the stress in the feed intake section and the transmission
and  increase  the  possibility  of  working  with  the  machine  continuously  without
blockages.  Be  aware  that  adjustment  for  short  cutting  length  increases  the  power
consumption and also the wear of blades.
Always work with sharp blades and correctly adjusted shear-bar.

Under difficult conditions we recommend you to bring spare friction discs for the slip
clutch  on  the  auger  since  these  are  worn  each  time  the  clutch  is  activated.  After
some time the power which can be transmitted is reduced so much that the capacity
of  the  machine  is  lowered  and  the  friction  discs  must  be  replaced.  When  replacing
discs  remember  that  they  must  be  of  the  same  number  and  quality  so  that  the
required torque can be transmitted and to secure maximum life.

SWATHING BEFORE CHOPPING

If  it  is  possible  to  influence  the  swathing  made  before  chopping  it  is  important  to
emphasise  that  regular  and  even  swaths  are  optimal  for  the  subsequent  chopping
and will spare the tractor driver a lot of trouble.

The machine is equipped with a wide pick-up and if you want to use the capacity of
the machine through double swathing, it is desirable to place 2 swaths beside each
other  within  the  width  of  the  pick-up  instead  of  raking.  Raked  swaths  are  often
irregular and the crop tangled which may cause blockages in the auger and/or feed
intake section.
Therefore, double swaths are optimal for a regular flow of crop through the machine.

«
...
71
72
73
74
75
...
»

Содержание FCT King Size 1260



















































































































Отзывы:

Нет отзывов

Похожие инструкции для FCT King Size 1260

Бренд: Campbell Страницы: 18

Бренд: Vector Страницы: 4

Бренд: FEAS Страницы: 72

Бренд: Facsimile Страницы: 16

Бренд: Campbell Страницы: 2

Бренд: Eaton Страницы: 2

Бренд: Eaton Страницы: 20

Бренд: Ecler Страницы: 108

Бренд: R&S Страницы: 121

Бренд: Launch Страницы: 3

Бренд: Launch Страницы: 43

Бренд: Launch Страницы: 8

Бренд: Launch Страницы: 67

Бренд: Launch Страницы: 55

Бренд: LAUNCH TECH Страницы: 14

X-431 PROS V4.0

Бренд: Launch Страницы: 80

Бренд: Octane Fitness Страницы: 20

Бренд: Oceaneering Страницы: 27

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды