JF FCT King Size 1260 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 114

background image

1. INTRODUCTION

PIGB-206X-02 FCT1460 0614

- 11 -

DEFINITIONS

The safety decals and the instruction manual of the machine contain a line of safety
notes. The safety notes mention certain measures, which we recommend you and
your colleagues to follow as to increase the personal safety as much as possible.
We recommend that you take the necessary time to read the safety instructions and
inform your staff to do the same.

In this instruction manual this symbol is used with reference to
personal safety directly or indirectly through maintenance of the
machine.

CAUTION:

The word CAUTION is used to ensure that the operator follows the
general safety instructions or the measures mentioned in the
instruction manual to protect the operator and others against injuries.

WARNING:

The word WARNING is used to warn against visible or hidden risks,
which might lead to serious personal injuries.

DANGER:

The word DANGER is used to indicate measures which, according to
legislation, must be followed to protect oneself and others against
serious injuries.

GENERAL SAFETY INSTRUCTIONS

The following is a brief description of the measures, which should be a matter of
common knowledge to the operator.

1. Always disengage the PTO drive shaft, activate the parking brake of the tractor,

stop the tractor engine and remove the ignition key before you:

-

lubricate the machine,

-

clean the machine,

-

disassemble any part of the machine,

-

adjust the machine.

2. Always block the wheels before working under the machine.

3. Never start the tractor until all persons are at a safe distance away from the

machine.

4. Make sure that all tools have been removed from the machine before starting

the tractor.

5. Make sure that all guards have been mounted correctly and locked where

appropriate.

«
...
9
10
11
12
13
...
»

Содержание FCT King Size 1260



















































































































Отзывы:

Нет отзывов

Похожие инструкции для FCT King Size 1260

Бренд: ACCU-CHECK Страницы: 104

Бренд: Parker Страницы: 64

Бренд: Parker Страницы: 40

Matrx Digital MDM

Бренд: Parker Страницы: 20

TUV COMFORT LIGHT Series

Бренд: olympia electronics Страницы: 4

NTP TECHNOLOGY DAD Thunder Core 256

Бренд: DAN Страницы: 16

Retractable Box Scrapers HR3584

Бренд: Land Pride Страницы: 1

CareTips Provox FreeHands FlexiVoice

Бренд: Atos Medical Страницы: 2

Бренд: Petromax Страницы: 16

Бренд: SereneLife Страницы: 4

SnapTable PRO Hyper-Lite

Бренд: SWENSON SHEAR Страницы: 12

Бренд: Etesia Страницы: 28

Fast Track Solo

Бренд: Avid Technology Страницы: 24

Nebula Blizzard v3

Бренд: Lanta Страницы: 8

Бренд: Eagle Страницы: 38

Oxford Standing Harness

Бренд: Joerns Страницы: 8

Бренд: Xante Страницы: 27

Бренд: Celco Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды