JF FCT King Size 1260 Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 114

background image

2. CONNECTION TO TRACTOR

PIGB-206X-02 FCT1460 0614

- 24 -

2. CONNECTION TO TRACTOR

THE HYDRAULIC SYSTEM

HYDRAULIC CONNECTION

DANGER:

The hydraulic components must not be exposed to a higher
working pressure than 210 bar as a higher working pressure
may gradually cause parts to be damaged. Hereby a serious risk
of personal injury occurs.

CAUTION:

It  is  important  that  the  quick-release  couplings  are  always  carefully
cleaned  before  mounting  to  avoid  impurities  contaminating  the
hydraulic system and damaging important valve functions. When the
hydraulic  hoses  are  not  connected  to  the  tractor  they  should  be
parked in the holder at the end of the drawbar.

The machine is equipped with its own hydraulic system, which must be supplied with
oil from the tractor.
The  system  is  used  for  pick-up  lifting,  drawbar,  chute  swivelling,  deflector,  chute
folding  and  reverse  function.  None  of  these  functions  use  very  much  oil  and  are
controlled in the best way when the oil flow is low. Adjust the oil flow from the tractor
to 15-20l/min., or as low as possible.
Connect  the  hoses  to  a  double-acting  outlet  on  the  tractor,  or  better:  connect  the
pressure hose to the A-port on the hydraulic outlet and the return hose to a free flow
return-port directly to rear-axle assembly. Hereby you ensure that the return pressure
is sufficiently low. This is especially important if the oil flow from the tractor cannot be
adjusted to a sufficiently low level.

IMPORTANT:

The hydraulic outlet of the chosen A-port must be locked in pressure
position to ensure continuous oil flow to the machine’s hydraulic
system.

«
...
22
23
24
25
26
...
»

Содержание FCT King Size 1260



















































































































Отзывы:

Нет отзывов

Похожие инструкции для FCT King Size 1260

Бренд: Panasonic Страницы: 174

Бренд: PANDROL Страницы: 36

Бренд: Badger Basket Страницы: 7

Бренд: Backyard Discovery Страницы: 53

Бренд: IDEAL Networks Страницы: 60

Бренд: IceCure Страницы: 104

Бренд: Cannon Страницы: 70

Бренд: Sakai Страницы: 31

Бренд: Ideal Heating Страницы: 16

Бренд: PMK Страницы: 24

Бренд: SteelFlex Страницы: 13

Spectral M950 Q4 Tour

Бренд: SHOWTEC Страницы: 24

Бренд: Ibiza Страницы: 20

Бренд: Murphy Страницы: 20

Бренд: REITEL Страницы: 20

Бренд: Velleman Страницы: 4

Advisor Guide Pedestrian Signal

Бренд: Campbell Страницы: 14

Бренд: Handicare Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды