JF FCT King Size 1260 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 114

background image

1. INTRODUCTION

PIGB-206X-02 FCT1460 0614

- 13 -

LOCKING OF GUARDS

All hinged guards on the machine are equipped with a lock. The lock ensures that the
guard cannot be opened without tools. There are two different types of lock. Fig. 1-1
shows the locking principle and the corresponding transfer which indicates and
illustrates the locks on the machine.

CHOICE OF TRACTOR

Always follow the recommendations specified in the instruction manual of the tractor.
If this is not possible, technical assistance must be sought.
Legal transport of the machine on public roads requires a tractor with sufficient mass
and braking capacity.
Choose a tractor which has minimum 103 KW/140 HP at the power take-off but
cannot deliver more than 200 KW/280 HP.
The machine is as standard constructed for 1000 RPM, and is delivered from the
factory with 1 3/4" PTO drive shaft with 20 spline yoke.

As an alternative 1 3/4’’ yokes

with 6 spline, 1 3/8” yokes with 6 spline and finally 1 3/8” yokes with 21 spline can be
supplied for the PTO drive shaft of the machine

A suitable tractor will have a broad range of gears for driving speeds between 5 and
8 km/h.
The tractor hydraulic system should deliver at least 170 bar and the tractor’s
pressure relief valve should not allow more than 210 bar.

The drawbar of the forage harvester is delivered with a drawing eye, for which reason
the tractor should preferably have a clevis drawbar. The drawbar pin should be 30
mm diameter.

Always choose a tractor with a closed cab when working with a precision chopper.

Fig. 1-1

P

R

1

1

-0

2

4

3

PR80-0819

Guard

«
...
11
12
13
14
15
...
»

Содержание FCT King Size 1260



















































































































Отзывы:

Нет отзывов

Похожие инструкции для FCT King Size 1260

Бренд: ABB Страницы: 6

Бренд: Makerfire Страницы: 10

Бренд: K&K Страницы: 8

Бренд: Yamaha Страницы: 78

Бренд: Fast Страницы: 42

Бренд: DARAY Страницы: 28

Бренд: Backyard Play Systems Страницы: 64

Бренд: Haenim Страницы: 2

Бренд: CAIRE Страницы: 2

Бренд: Ultimaker Страницы: 38

Бренд: A&D Страницы: 2

Бренд: A&D Страницы: 176

Бренд: Baroness Страницы: 40

Бренд: Baroness Страницы: 40

Бренд: BARKO LOADERS Страницы: 85

Бренд: Campbell Страницы: 2

Бренд: IBS Scherer Страницы: 64

Бренд: HANYOUNG NUX Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды