JF FCT King Size 1260 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 114

background image

1. INTRODUCTION

PIGB-206X-02 FCT1460 0614

- 12 -

6. During work never wear loose clothes or have your hair hang down as it may be

pulled in by the moving parts of the machine.

7. Always wear suitable shoes to avoid falling.

8. Do not change the guards or work with the machine when a guard is missing or

defective.

9. Always drive with the statutory lights and safety marking during transport on

public roads and at night.

10. Limit the transport speed to maximum 30 km/h if the machine has not been

marked with another maximum speed limit.

11. Do not stand near the machine while it is working.

12. When mounting the PTO drive shaft, check that the number of rpm and the

direction of rotation of the tractor match those of the machine.

13. Always use hearing protectors if the noise from the machine is annoying or if

you are working with the machine for a considerable period in a tractor cabin,
which has not been silenced sufficiently.

14. Never allow anybody to be on the machine during work or transport.

15. Never use the machine for other purposes than what it has been constructed

for.

16. Do not allow any children to be near when you are working with the machine.

17. Never stand between the tractor and the machine during connection and

disconnection.

18.  Do not feed material into the cutting unit, using hands or feet, while it is working.

19.  Do not try to remove material from the cutting unit while it is working.

20.  If material must be removed from the forage harvester, the PTO shaft must be

disconnected completely. Stop the engine and remove the ignition key.

«
...
10
11
12
13
14
...
»

Содержание FCT King Size 1260



















































































































Отзывы:

Нет отзывов

Похожие инструкции для FCT King Size 1260

Бренд: B&K Страницы: 8

Бренд: Palazzetti Страницы: 112

Бренд: Landoll Страницы: 52

Бренд: Gason Страницы: 110

Бренд: Gainsborough Страницы: 2

Бренд: JB Systems Страницы: 12

Бренд: KBT Страницы: 12

ABS-Lock DH04 Series

Бренд: ABS Страницы: 4

Бренд: Kamikaze Страницы: 112

Бренд: KAM Страницы: 2

Бренд: Haas Страницы: 12

Бренд: SaMASZ Страницы: 25

Бренд: V.ORLANDI Страницы: 144

Бренд: KCI Страницы: 2

Бренд: KCI Страницы: 60

Бренд: Landoll Страницы: 38

Бренд: GE Страницы: 18

Бренд: LSI Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды