janitza UMG 96 RM-M Скачать руководство пользователя страница 19

Страница: 19 / 112

UMG 96RM-M

Attention!
Voltages that exceed the permitted
ratedmains voltages must be connected
via voltage transformers.

Attention!
The UMG 96RM-M is not suitable for
the measurement of DC voltages.

Attention!
The voltage measurement inputs on
the UMG 96RM-M are dangerous
to touch!

When connecting the voltage to be measured,
the following must be observed:

Isolation device
• A suitable circuit breaker must be fitted to disconnect

and de-energise the UMG 96RM-M.

• The circuit breaker must be placed in the vicinity of

the UMG 96RM-M, be marked for the user and easily
accessible.

• The circuit breaker must be UL/IEC certified.

Overcurrent protection device
• An overcurrent protection device must be used for

line protection.

• For line protection, we recommend an overcurrent

protection device as per the technical specifications.

• The overcurrent protection device must be suitable

for the line cross section used.

• The overcurrent protection device must be UL/IEC

certified.

• A circuit breaker can be used as an isolating and line

protection device. The circuit breaker must be UL/IEC
certified.

• Measured voltages and measured currents must

derive from the same network.

Содержание UMG 96 RM-M

















































































































Результаты поиска

Содержание UMG 96 RM-M

Отзывы:

Похожие инструкции для UMG 96 RM-M

Бренды по названию

Популярные бренды

janitza UMG 96 RM-M, Руководство пользователя и технические данные

Результаты поиска

Содержание UMG 96 RM-M

Отзывы:

Похожие инструкции для UMG 96 RM-M

Бренды по названию

Популярные бренды