janitza UMG 96 RM-M Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 112

background image

39

UMG 96RM-M

Programming current transformers

Switching to programming mode
• Simultaneously press buttons 1 and 2 in order

to switch to programming mode. If a user password
was programmed, the password request will appear
with "000". The first digit of the user password flashes
and can be changed with button 2. The next digit is
selected by pressing button 2 and will begin flashing.
If the correct combination was entered or if no user
password was programmed, the device will enter pro-
gramming mode.

• The symbols for the programming mode (PRG) and for

the current transformer (CT) appear.

• Confirm the selection with button 1.
• The first digit of the input area for the primary current

starts flashing.

Current transformer primary current input
• Change the flashing digit with button 2.
• Select the next digit to be changed with button 1.

The selected digit to be changed starts flashing.
If the entire number is flashing, the decimal point can
be moved with button 2.

Current transformer secondary current input
•  Only 1 A or 5 A can be set as the secondary current.
•  Select the secondary current with button 1.
•  Change the flashing digit with button 2.

Leaving programming mode
• Simultaneously press buttons 1 and 2 to exit the pro-

gramming mode.

«
...
37
38
39
40
41
...
»

Содержание UMG 96 RM-M

















































































































Отзывы:

Нет отзывов

Похожие инструкции для UMG 96 RM-M

Бренд: LaMotte Страницы: 2

Бренд: FCI Страницы: 44

Бренд: FCI Страницы: 36

Бренд: FCI Страницы: 26

Бренд: Hach Страницы: 28

Бренд: NCTE Страницы: 10

NANOCOLOR UV/VIS II

Бренд: Macherey-Nagel Страницы: 99

Бренд: Xylem Страницы: 19

Бренд: LaserLiner Страницы: 64

Бренд: horiba Страницы: 103

MRG 512 PQ Flex

Бренд: janitza Страницы: 9

Бренд: Underground Magnetics Страницы: 53

Бренд: PASCO Страницы: 2

Бренд: Topcon Страницы: 80

Бренд: Ralcam Страницы: 8

Бренд: Crowcon Страницы: 37

Бренд: Sensitech Страницы: 2

Бренд: Wallbox Страницы: 66

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды