janitza UMG 96 RM-M Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 112

background image

42

UMG 96RM-M

Device address (addr. 000)

If several devices are connected to one another
via the M-Bus interface, a master device can only
differentiate between these devices by means of their
device addresses. Therefore, each device in a network
must have a different device address. Addresses can be
set in the range from 1 to 250.

C

The adjustable range of the device
address is between 0 and 255. The values
0 and 251 to 255 are reserved and may
not be used.

Secondary device address (addr. 081-084)

The secondary address provides - in addition to the pri-
mary address - a further opportunity to speak directly to
the device within the bus system.

The composition of the secondary address is broken
down into a device-specific section and an extended
section:

• The secondary address is comprised of 8 Bytes and

is coded as BCD.

• The extended section of the secondary address is

pre-assigned with the device serial number. This sec-
tion can be changed by the customer (addr. 081- 084).

• The device-specific section of the secondary address

cannot be changed.

XX XX XX XX 2E 28 09 02

Extended section, 8 digits

Device-specific section,
8 digits

Version, 2 digits
Internal release, 2 digits
Manufacturer ID, 4 digits
Extended section, 4th part
Extended section, 3rd part
Extended section, 2nd part
Extended section, 1st part

«
...
40
41
42
43
44
...
»

Содержание UMG 96 RM-M

















































































































Отзывы:

Нет отзывов

Похожие инструкции для UMG 96 RM-M

Бренд: Van Walt Страницы: 2

Бренд: B meters Страницы: 2

Бренд: Cannon Страницы: 64

Бренд: Cannon Страницы: 73

Бренд: Hach Страницы: 28

YPP-100 Light Piano

Бренд: Yamaha Страницы: 54

Бренд: Yamaha Страницы: 44

Бренд: Yamaha Страницы: 56

Бренд: Yamaha Страницы: 10

Бренд: Yamaha Страницы: 32

Бренд: Major tech Страницы: 16

Бренд: Zoetis Страницы: 2

Бренд: Palstar Страницы: 15

International 2S Pro

Бренд: Brantz Страницы: 2

Бренд: Salutron Страницы: 2

Ocean Optics HR2000 Series

Бренд: Halma Страницы: 42

Бренд: Roland Страницы: 2

LASERSCALE BL55-RU Series

Бренд: Magnescale Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды