janitza UMG 96 RM-M Скачать руководство пользователя страница 41

Страница: 41 / 112

UMG 96RM-M

Fig. Password request
If a password was set,
it can be entered using
buttons 1 and 2.

Fig. Current transformer
programming mode
The primary and
secondary currents can
be changed using buttons
1 and 2 (cf. page 39).

Fig. Programming mode
Voltage transformer
The primary and
secondary currents can
be changed using buttons
1 and 2 (cf. page 40).

Programming parameters

Switching to programming mode
• Switch to the programming mode as described. The

symbols for the programming mode (PRG) and for the
current transformer (CT) appear.

• Use button 2 to switch to the voltage transformer

setting. The first parameter of the parameter list
is shown by repeatedly pressing button 2.

Changing parameters
• Confirm the selection with button 1.
• The most recently selected address is displayed with

the associated value.

• The first digit of the address flashes and can be

changed using button 2. Button 1 provides a selection
of digits that, in turn, can be changed with button 2.

Changing the value
• Once the desired address is set, a digit of the value

is selected with button 1 and changed with button 2.

Leaving programming mode
• Simultaneously press buttons 1 and 2 to exit the

programming mode.

Fig. Programming mode
Parameter display
The individual parameters
can be changed
using buttons 1 and 2
(cf. page 36).

Содержание UMG 96 RM-M

















































































































Результаты поиска

Содержание UMG 96 RM-M

Отзывы:

Похожие инструкции для UMG 96 RM-M

Бренды по названию

Популярные бренды

janitza UMG 96 RM-M, Руководство пользователя и технические данные

Результаты поиска

Содержание UMG 96 RM-M

Отзывы:

Похожие инструкции для UMG 96 RM-M

Бренды по названию

Популярные бренды