ITT Goulds Pumps 3405 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 61

background image

WARNING:

Pumping equipment Instruction, Operation, and Maintenance manuals clearly identify accepted
methods for disassembling pumping units. These methods must be adhered to. Specifically,
applying heat to impellers and/or impeller retaining devices to aid in their removal is strictly for-
bidden. Trapped liquid can rapidly expand and result in a violent explosion and injury.

ITT Goulds Pumps will not accept responsibility for physical injury, damage, or delays caused by a failure
to observe the instructions for installation, operation, and maintenance contained in this Pump Safety
Manual or the current IOM available at www.gouldspumps.com/literature.

1.3 Safety

Definitions

Throughout this manual the words WARNING, CAUTION, ELECTRICAL, and ATEX are used to indicate
where special operator attention is required.

Observe all Cautions and Warnings highlighted in this Pump Safety Manual and the IOM provided with
your equipment.

WARNING:

Indicates a hazardous situation which, if not avoided, could result in death or serious injury.
Example: Pump shall never be operated without coupling guard installed correctly.

CAUTION:

Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
Example: Throttling flow from the suction side may cause cavitation and pump damage.

ELECTRICAL HAZZARD:

WARNING:

Indicates the possibility of electrical risks if directions are not followed.
Example: Lock out driver power to prevent electric shock, accidental start-up, and physical in-
jury.

ATEX:

WARNING:

When installed in potentially explosive atmospheres, the instructions that follow the Ex symbol
must be followed. Personal injury and/or equipment damage may occur if these instructions are
not followed. If there is any question regarding these requirements or if the equipment is to be
modified, please contact an ITT Goulds Pumps representative before proceeding.
Example: Improper impeller adjustment could cause contact between the rotating and station-
ary parts, resulting in a spark and heat generation.

1.3 Safety

3405-3406-3416 Installation, Operation and Maintenance Instructions

5

«
...
5
6
7
8
9
...
»

Содержание Goulds Pumps 3405






























































Отзывы:

Нет отзывов

Похожие инструкции для Goulds Pumps 3405

Бренд: Eaton Страницы: 20

Бренд: Eaton Страницы: 21

Бренд: salmson Страницы: 16

Бренд: Navien Страницы: 48

Бренд: Navien Страницы: 2

Naviels UKDAX-10EDT

Бренд: DAXOM Страницы: 28

Бренд: Sanden Страницы: 32

Бренд: Barnstead|Thermolyne Страницы: 56

Бренд: Edwards Страницы: 56

Бренд: Greencut Страницы: 54

Бренд: SOLARFOCUS Страницы: 52

Бренд: P.Lindberg Страницы: 46

FLOOD KING 240V

Бренд: U.S. Products Страницы: 8

Бренд: Watson-Marlow Страницы: 576

WH FLAT 50-100L

Бренд: ArTi Страницы: 34

AquaSurge PRO 2000-4000

Бренд: Aquascape Pro Страницы: 8

Бренд: York Страницы: 12

Бренд: Santon Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды