ITT Goulds Pumps 3405 Скачать руководство пользователя страница 47 | Manualshive

Страница: 47 / 61

background image

Part No.

Groups

Group M

Group L

332A

H 60222

K 60454

K 60771

332B

K3 64284

K3 63290

K 60810

333

H 60284

K 60478

K 60810

7.4 Dismantling of pump

The basic instructions are for a Model 3405 pump. Where dismantling of the Model 3406 or 3416 pumps
differ, the necessary supplementary instructions are included.

1.

Drain liquid from pump.

2.

Shut off and disconnect any auxiliary piping.

3.

Disconnect coupling.

4.

Remove gland assembly from stuffing boxes. See

7.2 Repacking stuffing boxes on page 37

5.

Jack and remove dowel pins from upper half casing by use of hex nut provided on top of pins. Re-
move nuts from casing parting studs and loosen upper half casing (100) by screwing two bolts
(½"-13 threads) in holes provided in the flange. Lift off upper half casing, being careful not to injure
the parting gasket. Use the lugs provided for lifting the upper half casing. Do not use these lugs for
lifting entire pump.

6.

Remove nuts from bearing cap studs and lift bearing cap (III) from unit.

NOTICE:

These caps must be replaced on the same end of pump from which they were removed.

They should be marked for identification before disassembly. The shims under the bearing caps
should be preserved and reused at reassembly. If lost or damaged, they must be replaced by shims
1/64" thick.

7.

Carefully lift rotating assembly from unit and place on padded supports which will not injure the
shaft sleeves.

8.

Note the distance from the end of the shaft to the face of the pump half coupling so that the cou-
pling half can be correctly positioned when reassembled. Pull the coupling half from pump shaft.

9.

Remove coupling key.

10. Remove cap screws on each end cover and remove end covers (109 and 119) from bearing hous-

ing (134 or 166). Preserve end cover gaskets (360). On the Model 3406 and 3416 the constant lev-
el oilers ( 251) must first be removed from both thrust and coupling end and the oil drained from the
bearing housings.

11. Remove snap ring (361) from shaft. Use No. 4 Waldes pliers. The Model 3416 has a shaft nut rath-

er than a snap ring.

12. Remove ball bearings (112 and 137) from shaft seat by the use of a bearing puller. Details of a rec-

ommended puller, capable of removing bearings from all three groups of pumps, are shown in Fig-
ure 19. Care must be used. Puller bar must be square with shaft so that equal pressure is applied
evenly to the circumference of the outer race of the bearing. A steady pressure must be applied to
the puller screw.

7.4 Dismantling of pump

3405-3406-3416 Installation, Operation and Maintenance Instructions

45

«
...
45
46
47
48
49
...
»

Содержание Goulds Pumps 3405






























































Отзывы:

Нет отзывов

Похожие инструкции для Goulds Pumps 3405

Бренд: A.O. Smith Страницы: 8

Бренд: Eaton Страницы: 29

Naviels UKDAX-10EDT

Бренд: DAXOM Страницы: 28

Бренд: Sanden Страницы: 32

Бренд: Bard Страницы: 26

PULSAR Shadow Series

Бренд: Pulsafeeder Страницы: 46

Бренд: Flux Страницы: 80

Бренд: Annovi Reverberi Страницы: 4

Бренд: P.Lindberg Страницы: 54

Бренд: GORMAN-RUPP PUMPS Страницы: 25

Бренд: Intex Страницы: 5

Бренд: Wacker Neuson Страницы: 58

Бренд: Rheem Страницы: 16

Wright Flow Technologies RTP Series

Бренд: Idex Страницы: 58

Warren Rupp SANDPIPER Beast SPB20

Бренд: Idex Страницы: 21

Poolex MEGALINE FI

Бренд: poolstar Страницы: 38

Бренд: Barmesa Pumps Страницы: 15

Бренд: SFA Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды