ITT Goulds Pumps 3405 Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 61

background image

3.4 Connection of water seal piping

Water seal piping is required only when pump is operating under suction lift or when single mechanical
seal is used. It is not necessary when pump is operating under suction head or when double mechanical
seal is furnished, in which cases the four openings in the stuffing box and casing must be plugged.

On all iron pumps or when the pump is handling hydro-carbons, solvents and similar liquids, a grease
lubricator, using a non-solvent grease, should be fitted into the tapped opening in stuffing boxes (

).

Figure 12:

If the liquid contains abrasives or paper stock particles (white water applications) or is gritty, omit the wa-
ter seal piping and plug the tapped openings in the casing. Pipe a clean water supply with a shut-off
valve to each of the openings at the top of stuffing boxes at a pressure slightly higher than the suction
pressure on the pump.

The water seal piping, when required, is shipped separately in the box of fittings accompanying the
pump. When this piping is used, one end is attached to the tapped opening in the casing and the other
end to the tapped opening on the top of the stuffing box with connectors furnished. See

view on page 39

.

3.5 Connection of piping to quenching gland

The stuffing box gland can be operated with or without quenching water. Quenching is recommended on
applications where the liquid pumped is:

1.

Bearing Housing Showing Slots for Gland Bolt Heads.

3.4 Connection of water seal piping

3405-3406-3416 Installation, Operation and Maintenance Instructions

23

«
...
23
24
25
26
27
...
»

Содержание Goulds Pumps 3405






























































Отзывы:

Нет отзывов

Похожие инструкции для Goulds Pumps 3405

Бренд: Calpeda Страницы: 16

Aerco AM Series

Бренд: Watts Страницы: 7

Optyma Blue OP-LGHE068NTA07D

Бренд: Danfoss Страницы: 8

Бренд: Powerhorse Страницы: 48

PVR50 Flanged Series

Бренд: Continental Hydraulics Страницы: 8

Бренд: Little Giant Страницы: 2

Duraclad Lime Tamer

Бренд: A.O. Smith Страницы: 2

Blue Diamond MaxiBlue

Бренд: Charles Austen Страницы: 20

Бренд: RBI Страницы: 44

Бренд: IMO Страницы: 11

Бренд: Wacker Neuson Страницы: 60

CLI U12 SD0F1110 NG B/U

Бренд: Velux Страницы: 56

Бренд: York Страницы: 12

Бренд: A.O. Smith Страницы: 4

Бренд: Bryant Страницы: 6

Бренд: Morrison Страницы: 23

Бренд: U-Line Страницы: 9

Бренд: Alpha Solar Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды