ITT Goulds Pumps 3405 Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 61

background image

Figure 20:

3.

Mark the location of the keyway on the outside of both the impeller hub and the locking sleeve (104)
at points "A" and "B'' in

Figure 21: Left hand pump on page 48

and

Figure 22: Right hand pump

. These marks will be used later to indicate that the keyways are in line.

4.

Assemble the shaft sleeve (104) that has a keyway in the threaded end but does not have spanner
wrench holes. Turn sleeve in a clockwise direction on shaft until the dimension from the threaded
end of the sleeve to the shaft shoulder at thrust bearing or outboard seat agrees with the dimension
on

Figure 22: Right hand pump on page 49

for right hand or

Figure 21: Left hand pump on page

for left hand rotation.

This dimension must be held as near as possible with the keyways in the shaft and sleeve in align-
ment.

For the Model 3416 substitute the following B dimensions for those shown on

Figure 21: Left hand

pump on page 48

Figure 22: Right hand pump on page 49

.

7.5 Reassembly of pump

3405-3406-3416 Installation, Operation and Maintenance Instructions

47

«
...
47
48
49
50
51
...
»

Содержание Goulds Pumps 3405






























































Отзывы:

Нет отзывов

Похожие инструкции для Goulds Pumps 3405

Бренд: Camplux Страницы: 44

Бренд: EBARA Страницы: 16

Бренд: EBARA Страницы: 40

Бренд: EBARA Страницы: 38

Бренд: EBARA Страницы: 40

Бренд: EBARA Страницы: 534

Бренд: EBARA Страницы: 60

Бренд: ebm-papst Страницы: 8

Бренд: JEC Страницы: 13

Бренд: veito Страницы: 40

Бренд: Panasonic Страницы: 55

Бренд: Atlas Copco Страницы: 137

Бренд: A.O. Smith Страницы: 119

BREDEL 701 Series

Бренд: Watson-Marlow Страницы: 25

SINGLE PACKAGE DUAL FUEL HEAT PUMP

Бренд: York Страницы: 8

Fre-Heater D Series

Бренд: Mueller Страницы: 34

Бренд: Serenity Страницы: 3

Бренд: KlimaTeknik Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды