ITT Goulds Pumps 3405 Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 61

background image

4.3
Adjustment of stuffing box gland

With pump running at rated speed, stuffing box glands can be adjusted. Draw gland nuts up evenly and
only one-sixth of a turn at a time, allowing sufficient time between adjustments for the packing to adjust
itself and the effect on the leakage to be observed. If any sign of heating is evident, shut off the pump
and allow the boxes to cool. Several starts may be necessary before the boxes run cool. Do not back off
the gland nuts on a hot box as this will usually result in liquid leaking between the outer edge of the pack-
ing and the stuffing box bore. It must be borne in mind that it takes newly-installed packing some time to
"run in" and that during this period, frequent attention and careful adjustments are necessary. See

5.1 Stuffing box on page 32

for final adjustments of gland.

4.4 Alignment - final

Final alignment can only be accomplished after unit has been run under actual operating conditions for a
sufficient length of time to bring the unit up to operating temperatures.

After this warm-up period has elapsed, stop the unit and immediately disconnect the coupling and check
the alignment.

Follow the alignment procedure as outlined in Alignment - initial, with the exception of Paragraph 6,
which allows for "growth" of the parts due to temperature difference between the driver and the pump.
However, at the operating temperature, the unit will be in correct horizontal and vertical parallel align-
ment when a straight edge rests evenly on both halves of coupling rims at four points 90° apart.

As cautioned in 6, changing alignment in one direction may alter the alignment in another. Check through
each alignment procedure after making any alignment change.

4.5 Doweling

Doweling is not required in Group "S" and "M" pumps. On these pumps, patented lock washers are fur-
nished which hold the pump and driver feet securely in place.

On Group "L" pumps, the pump and driver should be doweled after installation is complete and the unit is
in correct final alignment. Four #6 taper dowel pins are included in the box of fittings accompanying the
pump.

These pins have a taper of ¼" to the foot. The diameter at large end is 0.341" (approximately 11/32"')
and the recommended drill size is 9/32".

Drill through two diagonally opposite feet of the pump and driver into the bedplate. Use a reamer with a
taper of ¼" to the foot. Ream out the drilled holes so that dowels extend well into the bedplate but project
above the pump and driver feet.

If the operator so desires, the same size pins and method of doweling can be used on Series "S" and "M"
pumps in addition to the patented lock washers.

To determine the group of a particular size pump, see interchangeability list,

7.3 Sectional view on page

4.3

Adjustment of stuffing box gland

3405-3406-3416 Installation, Operation and Maintenance Instructions

31

«
...
31
32
33
34
35
...
»

Содержание Goulds Pumps 3405






























































Отзывы:

Нет отзывов

Похожие инструкции для Goulds Pumps 3405

Бренд: YANGTECH Страницы: 16

Бренд: Steinberg Страницы: 52

Ingenio VM 050 D400-3-E

Бренд: Atlantic Страницы: 69

Tranquility Low-Profile Series

Бренд: ClimateMaster Страницы: 76

Бренд: Day and Night Страницы: 18

NEXIS-VE Series

Бренд: salmson Страницы: 120

Altherma 3 R MT F+W

Бренд: Daikin Страницы: 68

Бренд: DAB Страницы: 25

Бренд: Sulzer Страницы: 4

Mainsboost Plus

Бренд: Stuart Turner Страницы: 28

Super T T6C60SC-B

Бренд: GORMAN-RUPP PUMPS Страницы: 38

Бренд: Sulzer Страницы: 42

Бренд: Atlantic Страницы: 24

Бренд: Hozelock Страницы: 6

DHE?18 SLi 25 A

Бренд: STIEBEL ELTRON Страницы: 22

Бренд: CountyLine Страницы: 20

Бренд: JABSCO Страницы: 4

Бренд: Alfa Laval Страницы: 34

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды