ITT Goulds Pumps 3405 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 61

background image

2 Installation

2.1 Location

Pumping unit should be placed as close as practical to the source of supply. Always allow sufficient head
room to remove the upper half casing of the pump and the rotating element. Floor space allotted to the
pumping unit should be sufficient for inspection and maintenance.

2.2 Prepare the foundation

1.

The foundation should be substantial in order to absorb any vibration and to form a permanent rigid
support for the bedplate. A concrete foundation poured on a solid footing, using a one-three-five
mix, of a liberal thickness to support the pumping unit is satisfactory.

2.

Foundation Bolts:

a) The location and size of the foundation bolts is shown on the outline assembly drawing sup-

plied for the pumping unit.

b) Each bolt should be installed with a pipe sleeve around it - to allow for adjustment. The inside

sleeve diameter should be 2½ to 3 times the diameter of the bolt. Place a washer between bolt
head and sleeve to hold bolt in position. Stuff waste around foundation bolts to prevent con-
crete from entering between the bolt and pipe sleeve. See

Figure 1: on page 10

.

c)

The foundation bolts should be of sufficient length so that they project through the nut approxi-
mately ¼" after allowance has been made for grouting (¾" to 1½"), the thickness of the bed-
plate, and the thickness of the foundation bolt nut. See

Figure 1: on page 10

Figure 1:

3.

Preparing Foundation for Mounting:

Prior to setting unit upon the foundation, clean the top surface of concrete.

a) Put the pumping unit in place on the wedges. The wedges should be placed at four points, two

below the approximate center of the pump and two below the approximate center of the driver
(See

Figure 2: on page 11

). Some installations may require additional wedges near the mid-

dle of the bedplate.

b) Be sure that coupling is disconnected between pump and driver.

c)

By adjustment of the wedges, bring the unit to an approximate level and provide for the proper
distance above the foundation for grouting (¾" to 1½"). Plumb the suction and discharge flang-
es. By further adjustment of the wedges, bring the coupling halves into reasonable alignment.
Check by method described in Section Alignment - initial, steps 4 through 6.

4.

After the wedges have been adjusted, tighten foundation bolts evenly but only finger tight.

2 Installation

10

3405-3406-3416 Installation, Operation and Maintenance Instructions

«
...
10
11
12
13
14
...
»

Содержание Goulds Pumps 3405






























































Отзывы:

Нет отзывов

Похожие инструкции для Goulds Pumps 3405

Бренд: GD Страницы: 55

Бренд: Davey Страницы: 8

Бренд: Oleo-Mac Страницы: 171

Бренд: Oase Страницы: 2

Aerco AM Series

Бренд: Watts Страницы: 7

Бренд: MasterCraft Страницы: 8

Бренд: A.O. Smith Страницы: 4

SMART GEYSER 2330-03

Бренд: Simer Страницы: 12

164 002 12-US - UP3-P 12V

Бренд: Marco Страницы: 12

Бренд: Wilden Страницы: 39

Бренд: Kärcher Страницы: 50

Бренд: Bock Water heaters Страницы: 36

THBF701 Master Series

Бренд: bluefin Страницы: 17

Бренд: Newton Страницы: 4

Бренд: Davey Страницы: 8

Бренд: TOHATSU Страницы: 99

Бренд: Commercial Electric Страницы: 15

Бренд: MULTIQUIP Страницы: 35

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды