ITT Goulds Pumps 3405 Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 61

background image

Figure 16:

This method can be used only when there is liquid under some pressure in the discharge line.
The original prime must be effected from some outside source. After subsequent idle periods,
open air vent valves and open valve in bypass line around discharge check and gate valves until
liquid flows from air vent openings. Close air vent valves and bypass valve, start pump and open
discharge gate valve.

The valve in bypass can be left open, in which event, during idle periods, loss through foot valve
is constantly replenished from discharge line. This system is used for automatic operation where
idle periods are of short duration and there is no danger of exhausting all liquid from discharge
line, due to a leaky foot valve. If the valve in the bypass is left open, as described above, the foot
valve must be capable of withstanding static head pressure of the system.

Priming by Ejector:

On suction lift installations, an ejector, operated by steam, compressed air, or water under pressure, and
connected to tapped opening in top of casing can be used to remove air from casing and suction line,
thus priming the pump.

Close discharge gate valve, open valve "E" in steam, air or water pressure supply line. Open valve "S" in
suction pipe of ejector connected to pump casing. Air will be evacuated and liquid will be drawn up into
suction pipe and pump casing. When all air is evacuated, start pump, close valve "S" and valve "E", and
open discharge gate valve.

4.1 Priming

3405-3406-3416 Installation, Operation and Maintenance Instructions

29

«
...
29
30
31
32
33
...
»

Содержание Goulds Pumps 3405






























































Отзывы:

Нет отзывов

Похожие инструкции для Goulds Pumps 3405

Бренд: Daikin Страницы: 27

Aquarea WH-MDF06E3E5 series

Бренд: Panasonic Страницы: 36

Бренд: A.O. Smith Страницы: 64

Бренд: A.O. Smith Страницы: 4

Бренд: A.O. Smith Страницы: 4

Бренд: A.O. Smith Страницы: 4

120 through 250 Series

Бренд: A.O. Smith Страницы: 74

Бренд: Galmet Страницы: 256

Бренд: T-MAG Страницы: 36

Бренд: DAB Страницы: 184

Waterfall Kit WFK8

Бренд: Beckett Страницы: 1

Бренд: Bryant Страницы: 4

Бренд: DAB Страницы: 72

altherma ERHQ014BAV3

Бренд: Daikin Страницы: 32

Vickers 25V Series

Бренд: Eaton Страницы: 11

GHS 1 1/2 GF 32

Бренд: GORMAN-RUPP PUMPS Страницы: 47

Duraclad Lime Tamer

Бренд: A.O. Smith Страницы: 2

Aquantia KHPMS-BI Series

Бренд: Kaysun Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды