150
Troubleshooting
—Continued
Can’t get 6.1 or 7.1 playback?
•
If no surround back speakers are connected, or Zone 2/3 is
being used, 6.1 and 7.1 playback is not possible.
•
If the “SB Mode (5ch)” is available in any sub-menu of the
“Listening Mode Setup” menu, make sure that it is not set
to “Off” (pages 106-112).
The volume cannot be set above 99?
•
When the levels of all speakers have been calibrated (page
94), the maximum volume setting may change.
Noise can be heard?
•
Using cable ties to bundle audio cables with power cords,
speaker cables, and so on may degrade the audio perfor-
mance, so don’t do it.
•
An audio cable may be picking up interference. Try reposi-
tioning your cables.
The Late Night function doesn’t work?
•
Make sure the source material is Dolby Digital (page 56).
The multichannel input doesn’t work?
•
Check the MULTI-CH IN connections (page 66).
•
Make sure that the multichannel input is assigned to the
correct input source (page 66).
•
Set the audio input signal format to Multich (page 67).
About DTS signals
•
When DTS program material ends and the DTS bitstream
stops, the RDC-7.1 remains in DTS listening mode and the
DTS indicator remains on. This is to prevent noise when
you use the pause, fast forward, or fast reverse function on
your player. If you switch your player from DTS to PCM,
because the RDC-7.1 does not switch formats immediately,
you may not hear any sound, in which case you should stop
your player for about three seconds, and then resume play-
back.
•
With some CD and LD players, you won’t be able to play-
back DTS material properly even though your player is
connected to a digital input on the RDC-7.1. This is usually
because the DTS bitstream has been processed (e.g., output
level, sampling rate, or frequency response changed) and
the RDC-7.1 doesn’t recognize it as a genuine DTS signal.
In such cases, you may hear noise.
•
When playing DTS program material, using the pause, fast
forward, or fast reverse function on your player may pro-
duce a short audible noise. This is not a malfunction.
There’s no picture?
•
Make sure that all video connecting plugs are pushed in all
the way.
•
Make sure that each video component is properly con-
nected.
•
Make sure that the proper setting is made for the “Video
Assign” sub-menu under the “Input Setup” menu (page
99).
•
On your TV, make sure that the video input to which the
RDC-7.1 is connected is selected.
•
While the Pure Audio listening mode is selected, the video
circuits are turned off and the RDC-7.1 outputs no video
signals.
The onscreen menus (OSD) don’t appear, or they
appear in an odd position?
•
Make sure that the proper setting is made for the “Video
Output Assign” sub-menu under the “Speaker/Output
Setup” menu (page 92).
•
Make sure that the proper setting is made for the “OSD
Setup” sub-menu under the “Preference” menu (page 120).
•
On your TV, make sure that the video input to which the
RDC-7.1 is connected is selected.
Reception is noisy, FM stereo reception is noisy, or
the FM STEREO indicator doesn’t appear?
•
Relocate your antenna.
•
Move the RDC-7.1 away from your TV or computer.
•
Press the [Tuning Mode] button to turn off the “AUTO”
indicator, bringing the FM mode to monaural (page 62).
•
When listening to an AM station, operating the remote con-
troller may cause noise.
•
Passing cars and airplanes can cause interference.
•
Concrete walls weaken radio signals.
•
If nothing improves the reception, install an outdoor
antenna.
When the RDC-7.1 is unplugged or a power failure
occurred:
•
Normally, the built-in memory retains its contents for 2
weeks. If it loses radio presets, make the presets again.
The remote controller doesn’t work?
•
Make sure that the batteries are installed with the correct
polarity (page 9).
•
Install new batteries. Don’t mix different types of batteries
or old and new batteries (page 9).
•
Make sure that the remote controller is not too far away
from the RDC-7.1, and that there’s no obstruction between
the remote controller and the RDC-7.1’s remote control
sensor (page 9).
•
Make sure that the RDC-7.1 is not subjected to direct sun-
shine or inverter type fluorescent lights. Relocate if neces-
sary.
•
If the RDC-7.1 is installed in a rack or cabinet with colored
glass doors, the remote controller may not work reliably
when the doors are closed.
•
Make sure you’ve selected the correct remote controller
mode (page 51).
•
When using the remote controller to control other manufac-
turers’ AV components, some buttons may not work as
expected.
•
Make sure you’ve entered the correct remote control ID.
•
If you change the remote controller’s transmission signal
format to RF, be sure to select the same ID as the RF
receiver.
Can’t control other components?
•
If it’s an IntegraRESEARCH component, make sure that
the
cable and analog audio cable (RCA/phono) are
connected properly. Connecting only an
cable won’t
work (page 45).
•
Make sure you’ve selected the correct remote controller
mode (page 51).
Video
Tuner
Remote Controller
Содержание Integra Research RDC-7.1
Страница 1: ...AV Controller RDC 7 1 Instruction Manual...
