70
Enjoying Movies and Music in the Remote Zone (Zone 2/3)
—Continued
Operating with the Remote Controller
When operating with the remote controller, how to
operate depends on the location of Zone 2 or Zone 3, or
the distance from the RDC-7.1.
• Point the remote controller at the infrared receiver on
the RDC-7.1, and then operate the controller.
• Install a remote controller sensor in Zone 2 or Zone 3
through an IR connection (See pages 46-49).
• Switch the Transmission Signal Format to RF (Radio
Frequency) (depending on the destination) (See page
141).
Operating on the RDC-7.1
1
Power on the devices in Zone 2 or Zone 3.
Press the [Zone 2] or [Zone 3] button, and then
the [On] button.
2
Select a source.
Rotate the scroll wheel to select a source while
the [Zone 2] or [Zone 3] button is lighted (if the
button is not lighted, press the [Zone 2] or [Zone
3] button to light it).
• When you have selected the tuner, you can
choose a preset channel with the [CH Disc
+/–] button.
3
Adjust the volume level.
Press the [Zone 2] (or [Zone 3]) button, and
within 5 seconds, press the [Level –/+] button to
adjust the volume level.
Notes:
• When the pre-main amplifier or receiver is
connected, the volume level should be adjusted
at the connected component side.
• When not using Zone 2 or Zone 3, press the
[Zone 2] (or [Zone 3]) button, and then press
the [Standby] button.
ABC
DEF
PQRS
TUV
WXYZ
GHI
JKL
MNO
Caps
Delete
Language
Loca t ion
Album
Ar tist
Genre
Playlist
Repeat
Video
Music
Photo
@.-'/
--/---
Direct Tuning
#
Custom
Display
Dimmer
T V
Input
Sleep
Random
Main A Main B
Muting
Angle
Subtitle
Audio
Memory
Search
A-B
Repeat
On
Standby
T V
T V CH
T V VOL
RC-554M
Exit
Gu
ide
Rec
Last Memory
Prev
CH
Enter
Set
up
Retu
rn
Test Tone
CH SEL
Pure A
Surround
Direct
Stereo
Re-EQ
THX
All CH ST
Level +
Level -
L Night
Audio SEL
DSP
DSP
+10
0
Clear
1
2
3
4
5
6
7
8
9
Input
To
p M
enu
Men
u
VOL
CH
Disc
I
+
-
+
-
Zone 3
Zone 2
Input
Mode
Macro
Se
rve
r
Aud
io
A
D
J
CH Disc +/–
On, Standby
Level –/+
Zone 2
Zone 3
1
Turn on the power supply to the RDC-7.1, and
then select a source for Zone 2 or Zone 3.
For Zone 2
:
Press the [Zone 2] button, and then
select the source with the input source buttons.
The indicator above the selected input source
button will light green.
For Zone 3
:
Press the [Rec/Zone 3] button, and
then, select the source with the input source but-
tons. The indicator above the selected input
source button will light red.
When you press the [Zone 2] or [Rec/Zone 3]
button, the [Standby] indicator on the RDC-7.1
blinks for three seconds, so perform operations
while it is blinking.
When the same input source is selected for Zone
2 and Zone 3, it will light orange.
To switch the source for Zone 2 (or Zone 3) and
the main room simultaneously:
Repeatedly press the [Zone 2] (or [Rec/Zone 3])
button to display “Z2Sel:SOURCE,” and then
select the source.
2
Adjust the volume level.
For Zone 2
:
Press the [Zone 2] button, and then
adjust with the [Master Volume] dial.
For Zone 3
:
Press the [Rec/Zone 3] button, and
then adjust with the [Master Volume] dial.
Notes:
• When a pre-main amplifier or receiver is con-
nected to the RDC-7.1, the volume level
should be adjusted at the connected component
side.
On
Standby/On
Standby
Pure Audio
On
Master Volume
Power
DVD
Video
1
Video
2
Video
3
Video
4
Video
5
Video
6
Video
7
Tape
1
Tape
2
Tuner
Phono
Net Audio
C D
Open/Close
Zone
2 (
)
GRN
Rec/ Zone
3 (
)
RED
O f f
Phones
Clear
Rec/ Zone
3
Zone
2
Off
DSP
Display
Tuning
Tuning Mode
Preset
Memory
Setup
Exit
Enter
Dimmer
AV Controller
RDC-7.1
Zone 2
Master Volume
Standby/On
Off
Rec/Zone 3
Input source buttons and
indicators
Standby indicator
Содержание Integra Research RDC-7.1
Страница 1: ...AV Controller RDC 7 1 Instruction Manual...
