manualshive.com logo in svg

Inovance SV660, Руководство для продвинутых пользователей, Страница: 59 / 426

Поделиться
Скачать
Inovance SV660 Скачать руководство пользователя страница 59

-58-

3 Wiring

 

■

Three-phase 220 V Models: SV660NS6R6I

Noise filter

L1

L2
L3

U

V

W

ALM-

ALM

+

24V

COM

P

D
C

CN2

Three-phase 220 VAC

Surge 

protection 

device

1D

1Ry

1KM

Main circuit 

power input 

contactor

RUN 

button

STOP 

button

Servo alarm 

output relay

Servo alarm 

indicator

Servo alarm 

signal output

660N servo drive

M

PG

Figure 3-8 

Main circuit wiring of three-phase 220 V models

NOTE

 

◆

1KM: Electromagnetic contactor; 1Ry: Relay; 1D: Flywheel diode

 

◆

DO is set as alarm output (ALM+/-). When the servo drive alarms, the power supply will be cut off 

automatically and the alarm indicator will be turned on.

3.2.5 Precautions for Main Circuit Wiring

 

■

Do not connect the input power cables to the output terminals U, V and W. Failure to comply will 

damage the servo drive.

 

■

When cables are bundled in a duct, the cooling effect will be deteriorated. In this case, take the 

reduction ratio of the allowable current into consideration.

 

■

When the temperature inside the cabinet is higher than the temperature limit of the cable, it is 
recommended to use a Teflon cable with a higher temperature limit. As the surface of regular cables 
may be easily hardened and cracked under a low temperature, take thermal insulation measures for 

cables laid in a low-temperature environment.

 

■

The bending radius of a cable must be 10 times longer than its outer diameter to prevent the 
internal conductor from breaking due to long-time bending.

 

■

Use cables with a rated voltage above 600 VAC and rated temperature above 75° C. Under 30° C 

ambient temperature and normal cooling conditions, the allowable current density of the cable 

cannot exceed 8 A/mm

2

 when the total current is below 50 A, or 5 A/mm

2

 when the total current is 

above 50 A. The allowable current density (A/mm

2

) can be adjusted based on the following formula 

in the case of high ambient temperature or bundled cables.

Allowable current density = 8 x Reduction coefficient of conductor current-carrying density x Current 
correction coefficient

Содержание SV660











































































































































































































































































































































































































































Отзывы:

Нет отзывов