manualshive.com logo in svg

Inovance SV660, Руководство для продвинутых пользователей, Страница: 102 / 426

Поделиться
Скачать
Inovance SV660 Скачать руководство пользователя страница 102

-101-

4 Keypad Display and Operations

Code

Name

Function

Description

Remarks

38

TouchProbe1

Touch probe 1

Invalid - Probe not triggered
Valid - Probe can be triggered

The probe logic is only related 

to the probe function (60B8h) 

instead of the terminal logic.

39

TouchProbe2

Touch probe 2

Invalid - Probe not triggered
Valid - Probe can be triggered

The probe logic is only related 

to the probe function (60B8h) 

instead of the terminal logic.

Output signal function description

01

S-RDY

Servo ready

Valid - Servo ready
Invalid - Servo not ready

The servo drive is ready to run.

02

TGON

Motor rotating

Invalid - Absolute value of the 

filtered motor speed smaller 

than the value of H06-16.
Valid - Absolute value of the 

filtered motor speed reaching 

the value of H06-16.

-

09

BRK

Brake output

Valid: Brake signal outputted
Invalid: Brake signal not 

outputted

-

10

WARN

Warning

Valid - Warning occurs on the 
servo drive
Invalid - No warning occurs on 
the servo drive or the warning 
has been reset

-

11

ALM

Fault

Valid - Fault occurs on the servo 
drive
Invalid - No fault occurs on the 
servo drive or the fault has been 
reset

-

25

CMP

Position 

comparison

Valid: Servo drive passing the 

target position comparison 
point

Invalid: Servo drive not passing 

the target position comparison 
point

-

32

EDM

Safety status

Valid: STO function triggered
Invalid: STO function not 

triggered

The EDM will output valid 
signals only when the 24 V input 
voltages for STO1 and STO2 are 
disconnected simutaneously.

1  Forced DI signal

When this function is enabled, all DI levels will be controlled by H0D-18 (Forced DI value).

Содержание SV660











































































































































































































































































































































































































































Отзывы:

Нет отзывов