Inovance SV660 Скачать руководство пользователя страница 324 | Manualshive

Страница: 324 / 426

Inovance SV660 Скачать руководство пользователя страница 324

-323-

9 Troubleshooting

■

E740.3: Absolute encoder single-turn calculation error

Root Cause

Confirming Method

Solution

An internal fault occurs on the
encoder.

Check whether bit7 of H0B-28 is 1.

◆

Check whether the encoder

version (H00-04) is proper.

◆

Check whether encoder cables are
in proper condition.

◆

Replace the servo motor.

■

E740.6: Encoder write error

Direct cause:

A write error occurs on the encoder.

Root Cause

Confirming Method

Solution

An error occurs during writing the

position offset after angle auto-

tuning.

-

Check whether the encoder cable
shield and the grounding cable are
connected properly.

■

EB00.0: Position deviation too large

Direct cause:

The position deviation is larger than the value defined by 6065h in the position control mode.

Root Cause

Confirming Method

Solution

1. Power output (UVW) phase loss or

incorrect phase sequence occurs on
the servo drive.

Perform motor trial run without load

and check the cable connections.

Re-connect the cables according
to the correct wiring diagram or
replace the cables.

2. The servo drive UVW cables or the
encoder cables are disconnected.

Check the cable connections.

Re-connect the UVW cables. The
UVW phase sequence on the servo
drive side must be consistent with
that on the motor side. Replace
with new cables if necessary and
ensure the cables are connected
properly.

3. The motor rotor is locked due to
mechanical factors.

Check the RUN command and

motor speed (200B-01h) through
the software tool or the keypad:

RUN command in the position

control mode: 200B-0Eh
(Position reference counter)

RUN command in the speed control

mode: 200B-02h
(Speed reference)

RUN command in the torque control

mode: 200B-03h
(Internal torque reference)

Check whether the RUN command
in the corresponding mode is not 0
but the motor speed is 0.

Eliminate mechanical factors.

4. The servo drive gain is low.

Check the position loop gain and
speed loop gain of the servo drive.

1st gain: 2008-01h to 2008-03h
2nd gain: 2008-04h to 2008-06h

Adjust the gain manually or perform
gain auto-tuning.

«
...
322
323
324
325
326
...
»

Содержание SV660











































































































































































































































































































































































































































Отзывы:

Нет отзывов