manualshive.com logo in svg

IAI RoboNet, Руководство по эксплуатации

Поделиться
Скачать
IAI RoboNet Скачать руководство пользователя страница 114

 

 

94 

Part 1  Specification

 
The target position data, acceleration/deceleration data, speed data, positioning band data and push-current limiting value 
data can be changed while the actuator is moving. To do so, turn the CSTR “1” (ON) and keep it “1” (ON) for tdpf or more after 
the data has been changed.   
Also provide an interval of 1 Mt or more after the CSTR is turned “0” (OFF) until it is turned “1” (ON) again. 
An example of changing the speed and acceleration/deceleration is shown below.   
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

*1 twcsON 

≥

 1Mt 

*2 twcsOFF 

≥

 1Mt 

 
 
 
 

Caution 

 

1.  If speed data is not set, or the set speed is “0,” the actuator will remain stopped and no alarm will generate. 
2.  The speed data setting is changed to “0” while the actuator is moving, the actuator will decelerate to a stop.   
3.  Target position data must be set even if you only want to change the acceleration/deceleration or speed data.   
4.  Acceleration/deceleration and speed data must be set even if you only want to change the target position data. 

 

[1] 

[2] 

[3]

≥

 0

≤

 1Mt 

Speed and 

acceleration/deceleration data 

setting (PLC 

→

 GW) 

Actuator speed 

Speed n2 

Speed n3 

*1

*2

Содержание RoboNet















































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды