Husqvarna F2203P4 Скачать руководство пользователя страница 35

Страница: 35 / 381

201715-10

6 FORK, TRIPLE CLAMP

Sand the edges of the sliding bushings with 600 grit sandpa
per; then clean and grease the bushings.

Fork oil (SAE 4) (48601166S1) (

llill

p. 352)

Push on lower sliding bushing

Mount upper sliding bushing Q).

Info

Without using a tool, pull the stack slightly apart by
hand.

Warm up the outer tube in area

of the lower sliding bush-

ing.

Guideline

50 °C (122 °F)

Slide the outer tube onto the inner tube.

Hold the lower sliding bushing with the longer side of the

special tool.

Mounting tool (T14040S) (

llill

p. 370)

Press the sliding bushing all the way into the outer tube.

Position the support ring.

Hold the seal ring with the shorter side of the special tool.

Mounting tool (T14040S) (

llill

p. 370)

Press the seal ring and support ring all the way into the outer

tube.

Mount lock ring@.

Info

The lock ring must engage audibly.

Содержание F2203P4






























































































































































































































































































































































































Результаты поиска

Содержание F2203P4

Отзывы:

Похожие инструкции для F2203P4

Бренды по названию

Популярные бренды

Husqvarna F2203P4, Руководство по ремонту

Результаты поиска

Содержание F2203P4

Отзывы:

Похожие инструкции для F2203P4

Бренды по названию

Популярные бренды