Husqvarna F2203P4 Скачать руководство пользователя страница 254

Страница: 254 / 381

19 CLUTCH

252

Checking/correcting the fluid level of the h draulic clutch

Warning

Skin irritation

Brake fluid causes skin irritation.

- Keep brake fluid out of the reach of children.

- Wear suitable protective clothing and safety glasses.

- Do not allow brake fluid to come into contact with the skin, the eyes or clothing.

- Consult a doctor immediately if brake fluid has been swallowed.

- Rinse the affected area with plenty of water in the event of contact with the skin.

- Rinse eyes thoroughly with water immediately and consult a doctor if brake fluid comes into contact

with the eyes.

- If brake fluid spills on to your clothing, change the clothing.

Warning

Environmental hazard

Hazardous substances cause environmental damage.

- Dispose of oils, grease, filters, fuel, cleaning agents, brake fluid, etc., correctly and in compliance

with the applicable regulations.

Info

The fluid level rises with increasing wear of the clutch facing discs.

Never use DOT 5 brake fluid. It is silicone-based and purple in color. Oil seals and clutch lines are not

designed for DOT 5 brake fluid.

Avoid contact between brake fluid and painted parts. Brake fluid attacks paint.

Only use clean brake fluid from a sealed container.

(FE EU/AU, FE 350 US)

- Move the clutch fluid reservoir mounted on the handlebar

to a horizontal position.

- Remove screws

- Remove cover

with membrane

- Check the fluid level.

Fluid level below container 4 mm (0.16 in)

rim

If the fluid level does not meet specifications:

- Correct the fluid level of the hydraulic clutch.

I Brake fluid DOT 4 (

!!,!l

p. 352)

- Position the cover with the membrane. Mount and tighten

the screws.

Info

Clean up overflowed or spilled brake fluid immedi

ately with water.

Содержание F2203P4






























































































































































































































































































































































































Результаты поиска

Содержание F2203P4

Отзывы:

Похожие инструкции для F2203P4

Бренды по названию

Популярные бренды

Husqvarna F2203P4, Руководство по ремонту

Результаты поиска

Содержание F2203P4

Отзывы:

Похожие инструкции для F2203P4

Бренды по названию

Популярные бренды