Husqvarna F2203P4 Скачать руководство пользователя страница 23

Страница: 23 / 381

B03520-14

B03528-13

6 FORK, TRIPLE CLAMP

Clamp the fork leg with the axle clamp.

Release hydrostop unit

and remove it.

Info

Do not use an impact wrench.
Place a pan underneath since oil will run out.

Remove the cartridge from the fork leg.

Pressing tool (T14051) (

�

p. 371)

Info

Removing the O-ring seat from the cartridge usually

requires the application of considerable force.

Remove dust boot (D.
Remove fork protector ring f).

Info

The fork protector ring does not necessarily need to
be removed for repair work.

Remove lock ring @.

Info

The lock ring has a beveled end where a screwdriver
can be applied.

Warm up the outer tube in area G) of the lower sliding bush
ing.
Guideline

(122 °F)

Pull the outer tube from the inner tube with a jerk.

Info

Lower sliding bushing

must be pulled from its

bearing seat.

Содержание F2203P4






























































































































































































































































































































































































Результаты поиска

Содержание F2203P4

Отзывы:

Похожие инструкции для F2203P4

Бренды по названию

Популярные бренды

Husqvarna F2203P4, Руководство по ремонту

Результаты поиска

Содержание F2203P4

Отзывы:

Похожие инструкции для F2203P4

Бренды по названию

Популярные бренды