Husqvarna F2203P4 Скачать руководство пользователя страница 147 | Manualshive

Страница: 147 / 381

Husqvarna F2203P4 Скачать руководство пользователя страница 147

15 WIRING HARNESS, BATTERY

Recharging the batte

Warning

Risk of injury

Battery acid and battery gases cause serious chemical burns.

- Keep batteries out of the reach of children.
- Wear suitable protective clothing and safety glasses.

- Avoid contact with battery acid and battery gases.

- Keep sparks or open flames away from the battery.
- Only charge batteries in well-ventilated rooms.

- Rinse the affected area immediately with plenty of water in the event of contact with the skin.
- Rinse eyes with water for at least 15 minutes and consult a doctor immediately if battery acid and

battery gases get into the eyes.

Warning

Environmental hazard

Batteries contain environmentally-hazardous materials.

- Do not dispose of batteries as household waste.
- Return batteries to your authorized Husqvarna Motorcycles dealer or dispose of them at a collection

point for used batteries.

Warning

Environmental hazard

Hazardous substances cause environmental damage.

- Dispose of oils, grease, filters, fuel, cleaning agents, brake fluid, etc., correctly and in compliance

with the applicable regulations.

Info

Even when there is no load on the battery, it discharges steadily.

The charging level and the method of charging are very important for the service life of the battery.

Rapid recharging with a high charging current shortens the service life of the battery.

If the charging current, charging voltage, or charging time are exceeded, the battery will be destroyed.

If the battery is depleted by repeated starting, the battery must be charged immediately.

If the battery is left in a discharged state for an extended period, it will become over-discharged and sul

fated, destroying the battery.

The battery is maintenance-free.

311910-10

Preparatory work

- Remove the seat. (

�

p. 97)

Main work

- Connect the battery charger to the battery. Adjust the battery

charger.

EU battery charger

XCharge-professional

(00029095050)

(

!!ll

p. 356)

Alternative 1

US battery charger

XCharge-professional

(00029095051) (

!!ll

p. 357)

Alternative 2

UK battery charger

XCharge-professional

(00029095052) (

!!ll

p. 357)

145

«
...
145
146
147
148
149
...
»

Содержание F2203P4






























































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды