manualshive.com logo in svg

Husqvarna F2203P4, Руководство по ремонту

Поделиться
Скачать
Husqvarna F2203P4 Скачать руководство пользователя страница 104

12  FUEL TANK, SEAT, TRIM 

A 

102 

Warning 

Danger of poisoning 

Fuel is poisonous and a health hazard. 

- Avoid skin, eye and clothing contact with fuel.

Immediately consult a doctor if you swallow fuel.

Do not inhale fuel vapors.
In case of skin contact,  rinse the affected area with plenty of water.
Rinse the eyes thoroughly with water,  and consult a doctor in case of fuel contact with the eyes.

-

Change your clothing in case of fuel spills on them.

Warning 

Environmental  hazard 

Improper handling of fuel is a danger to the environment. 

Do not allow fuel to enter the groundwater,  the soil,  or the sewage system. 

-

Clean plug-in connection 

O 

of the fuel line thoroughly with

compressed air.

• 

Info

I 

Under no circumstances should dirt enter into the fuel 

line.  Dirt in the fuel line clogs the injection valve! 

Disconnect the plug-in connection of the fuel line. 

Info 

Remaining fuel may flow out of the fuel hose. 

Pull fuel screen 

8 

out of the connecting piece.

Insert the new fuel screen all the way into the connecting 

piece. 

Lubricate the O-ring and connect plug-in connection of the 

fuel line. 

Danger 

Danger of poisoning 

Exhaust gases are toxic and 

inhaling them may result in unconsciousness and 
death. 

- Always make sure there is sufficient ventilation

when running the engine.

Use an effective exhaust extraction system when

starting or running the engine in an enclosed
space.

-

Start the engine and check the response.

Содержание F2203P4






























































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды