Husqvarna F2203P4 Скачать руководство пользователя страница 22

Страница: 22 / 381

6 FORK, TRIPLE CLAMP

Disassembling the fork legs

Info

The operations are the same on both fork legs.

201700-10

Condition

The fork legs have been removed.
- Note down the current state of rebound damping

REB

(red adjuster on the right fork leg).

- Note down the current state of compression

damping

COMP

(white adjuster on the left fork leg).

- Open the adjusters on the rebound and compression damp

ing all the way.

- Clamp the fork leg in the area of the lower triple clamp.

I Clamping stand (T1403S) (

p. 370)

- Remove screw

fD.

Remove adjuster.

- Loosen the screw cover

C,.

I Mounting tool (T1404 7) (

p. 370)

Info

The cartridge cannot be taken off yet.

- Unclamp the fork leg.

- Slide the outer tube down. Drain the fork oil.

Содержание F2203P4






























































































































































































































































































































































































Результаты поиска

Содержание F2203P4

Отзывы:

Бренды по названию

Популярные бренды

Husqvarna F2203P4, Руководство по ремонту

Результаты поиска

Содержание F2203P4

Отзывы:

Бренды по названию

Популярные бренды