Husqvarna F2203P4 Скачать руководство пользователя страница 144

Страница: 144 / 381

15 WIRING HARNESS, BATTERY

142

Changing the main fuse

Warning

Fire hazard

Incorrect fuses overload the electrical system.

- Only use fuses with the required ampere value.

- Do not bypass or repair fuses.

Info

The main fuse protects all power consumers of the vehicle. It is located in the starter relay housing

under the air filter box lid.

Preparatory work
(FE EU/AU)

- Press and hold the kill switch � while the engine is idling

until the engine stops.

(FE 350 US)

- Press and hold the kill switch � while the engine is idling

until the engine stops.

(FE 350 SUS)

- While the engine is idling, turn the key in the ignition lock

to the position �-

- Remove the air filter box cover. (

!!l

p. 92)

Main work

- Take off protection caps

- Remove faulty main fuse fj.

Info

You can recognize a faulty fuse by a burned-out fuse

wiref).

A spare fuse

is located in the starter relay.

- Install a new main fuse.

I Fuse (58011109120) (

�

p. 281)

- Check that the electrical system is functioning properly.

•

Tip

Insert a spare fuse so that it is available if needed.

- Mount the protection caps.

Finishing work

- Install the air filter box cover. (

�

p. 92)

Содержание F2203P4






























































































































































































































































































































































































Результаты поиска

Содержание F2203P4

Отзывы:

Похожие инструкции для F2203P4

Бренды по названию

Популярные бренды

Husqvarna F2203P4, Руководство по ремонту

Результаты поиска

Содержание F2203P4

Отзывы:

Похожие инструкции для F2203P4

Бренды по названию

Популярные бренды