Husqvarna F2203P4 Скачать руководство пользователя страница 129

Страница: 129 / 381

14 WHEELS

Main work

- Check the wheel bearing for damage and wear.

If the wheel bearing is damaged or worn:

Change the rear wheel bearing. (

I!!;,!

p. 136)

- Clean and grease shaft seal rings

and contact surface

of the spacers.

Long-life grease (

I!!;,!

p. 354)

- Insert the spacers.

(FE EU/ AU, FE 350 US)

Clean and grease the wheel spindle.

I Long-life grease (

llill

p. 354)

- Position the rear wheel and insert wheel spindle

- Mount the chain.

✓ The brake linings are correctly positioned.

- Position chain adjuster@). Mount nut

C,,

but do not

tighten it yet.

- Make sure that chain adjusters

(s)

are fitted correctly on

adjusting screws

- Check the chain tension. (

p. 129)

- Tighten nut

C,.

Guideline

M20x1.5

80 Nm (59 lbf ft)

Info

The wide adjustment range of the chain adjusters

(32 mm (1 .26 in)) enables different secondary

ratios with the same chain length.

Chain adjusters

(s)

can be turned by 180

- Operate the foot brake lever repeatedly until the brake

linings are in contact with the brake disc and there is a

pressure point.

(FE 350 SUS)

- Clean and grease the wheel spindle.

I Long-life grease (

I!!;,!

p. 354)

- Position the rear wheel and insert wheel spindle

- Mount the chain.

✓ The brake linings are correctly positioned.

127

Содержание F2203P4






























































































































































































































































































































































































Результаты поиска

Содержание F2203P4

Отзывы:

Похожие инструкции для F2203P4

Бренды по названию

Популярные бренды

Husqvarna F2203P4, Руководство по ремонту

Результаты поиска

Содержание F2203P4

Отзывы:

Похожие инструкции для F2203P4

Бренды по названию

Популярные бренды