Husqvarna F2203P4 Скачать руководство пользователя страница 109

Страница: 109 / 381

12 FUEL TANK, SEAT, TRIM

12.12 Checking the fuel �ressure

Danger

Fire hazard

Fuel is highly flammable.

The fuel in the fuel tank expands when warm and can escape if overfilled.
-

Do not refuel the vehicle in the vicinity of open flames or lit cigarettes.

Switch off the engine for refueling.

Make sure that no fuel is spilled; particularly not on hot parts of the vehicle.

If any fuel is spilled, wipe it off immediately.

Observe the specifications for refueling.

Warning

Danger of poisoning

Fuel is poisonous and a health hazard.

- Avoid skin, eye and clothing contact with fuel.
-

Immediately consult a doctor if you swallow fuel.

Do not inhale fuel vapors.

In case of skin contact, rinse the affected area with plenty of water.

Rinse the eyes thoroughly with water, and consult a doctor in case of fuel contact with the eyes.

Change your clothing in case of fuel spills on them.

Keep fuels correctly in a suitable canister, and out of the reach of children.

Condition

The fuel tank is full.

Ensure that the battery voltage does not drop below 12.5 V.

The diagnostics tool is disconnected.

- Thoroughly clean the plug-in connection of the fuel line using

compressed air.

•

Info

Under no circumstances should dirt enter into the fuel

line. Dirt in the fuel line clogs the injection valve.

Press on the small metal plate and disconnect fuel hose con

nection

Info

Remaining fuel may flow out of the fuel hose.

Mount special tool@.

Pressure testing tool (61029094000) (

�

p. 361)

Mount special tool

with nozzle label

0,60.

Testing hose (61029093000) (

�

p. 361)

Position the hose end in a fuel cannister.

Guideline

Minimum size of fuel cannis- 10 I (2.6 US gal)

ter

Connect the diagnostics tool and start it.

107

Содержание F2203P4






























































































































































































































































































































































































Результаты поиска

Содержание F2203P4

Отзывы:

Бренды по названию

Популярные бренды

Husqvarna F2203P4, Руководство по ремонту

Результаты поиска

Содержание F2203P4

Отзывы:

Бренды по названию

Популярные бренды