Husqvarna F2203P4 Скачать руководство пользователя страница 287 | Manualshive

Страница: 287 / 381

background image

27 CLEANING, CARE

27.1

Cleaning the motorc}!cle

Note

Material damage

Components become damaged or destroyed if a pressure cleaner is used incorrectly.

The high pressure forces water into the electrical components, connectors, throttle cables, and bearings, etc.

Pressure which is too high causes malfunctions and destroys components.

Do not direct the water jet directly on to electrical components, connectors, throttle cables or bearings.
Maintain a minimum distance between the nozzle of the pressure cleaner and the component.
Minimum clearance

60 cm (23.6 in)

Warning

Environmental hazard

Hazardous substances cause environmental damage.

Dispose of oils, grease, filters, fuel, cleaning agents, brake fluid, etc., correctly and in compliance

with the applicable regulations.

Info

To maintain the value and appearance of the motorcycle over a long period, clean it regularly.
Avoid direct sunshine when cleaning the motorcycle.

1

/111111111111111

\\

401061-01

Close off the exhaust system to keep water from entering.

Remove coarse dirt particles with a gentle water jet.

Spray dirty parts with a normal commercial engine cleaner
and then brush off with a soft brush.

Info

Use warm water containing normal motorcycle cleaner

and a soft sponge.

Never apply motorcycle cleaner to a dry vehicle;

always rinse the vehicle with water first.

After rinsing the motorcycle with a gentle spray of water,
allow it to dry thoroughly.

Remove the closure of the exhaust system.

Warning

Danger of accidents

Moisture and dirt impair the

brake system.

Brake carefully several times to dry out and

remove dirt from the brake linings and the brake
discs.

After cleaning, ride the vehicle a short distance until the
engine warms up.

•

Info

I

The heat produced causes water at inaccessible loca
tions in the engine and on the brake system to evapo
rate.

After the motorcycle has cooled off, lubricate all moving parts
and bearings.

Clean the chain. (

�

p. 133)

285

«
...
285
286
287
288
289
...
»

Содержание F2203P4






























































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для F2203P4

Бренд: LAZER Страницы: 13

Бренд: KTM Страницы: 13

Бренд: Jialing Honda Страницы: 10

Бренд: N-Com Страницы: 32

Бренд: DYNATEK Страницы: 3

Бренд: DYNATEK Страницы: 8

Бренд: DYNATEK Страницы: 12

Бренд: TM Страницы: 80

Бренд: MOTO GUZZI Страницы: 48

Бренд: MOTO GUZZI Страницы: 198

2002 California Special Sport

Бренд: MOTO GUZZI Страницы: 155

Бренд: MOTO GUZZI Страницы: 357

Бренд: HAUL MASTER Страницы: 8

Бренд: Shad Страницы: 2

Бренд: Peugeot Motorcycles Страницы: 52

Бренд: Wunderlich Страницы: 2

Бренд: Razor Страницы: 6

MADISON 300 2018

Бренд: Malaguti Страницы: 120

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды