Husqvarna F2203P4 Скачать руководство пользователя страница 119

Страница: 119 / 381

14 WHEELS

Checking the tire air �ressure

Info

Low tire air pressure leads to abnormal wear and overheating of the tire.

Correct tire air pressure ensures optimal riding comfort and maximum tire service life.

Checking the tire condition

Info

Remove the protection cap.

Check the tire air pressure when the tires are cold.

Tire air pressure off road

front

1.0 bar (15 psi)

rear

11 .0 bar (15 psi)

Road tire pressure (FE 350 S US)

front

1 .5 bar (22 psi)

rear

2 bar (29 psi)

If the tire pressure does not meet specifications:

- Correct the tire pressure.

Mount protection cap.

Only mount tires approved and/or recommended by Husqvarna Motorcycles.

Other tires could have a negative effect on handling characteristics.

The type, condition, and air pressure of the tires all have a major impact on the handling of the motorcy

cle.

The tires mounted on the front and rear wheels must have a similar profile.

Worn tires have a negative effect on handling characteristics, especially on wet surfaces.

Check the front and rear tires for cuts, run-in objects, and

other damage.

If the tires have cuts, run-in objects, or other damage:

- Change the tires.

Check the tread depth.

•

Info

Adhere to the legally required minimum tread depth.

Minimum tread depth

I �

2 mm (� 0.08 in)

If the tread depth is less than the minimum tread depth:

- Change the tires.

117

Содержание F2203P4






























































































































































































































































































































































































Результаты поиска

Содержание F2203P4

Отзывы:

Похожие инструкции для F2203P4

Бренды по названию

Популярные бренды

Husqvarna F2203P4, Руководство по ремонту

Результаты поиска

Содержание F2203P4

Отзывы:

Похожие инструкции для F2203P4

Бренды по названию

Популярные бренды