Husqvarna F2203P4 Скачать руководство пользователя страница 24

Страница: 24 / 381

6 FORK, TRIPLE CLAMP

Removing the s ring

Info

- Remove upper sliding bushing

@).

Info

Without using a tool, pull the stack slightly apart by

hand.

- Take off lower sliding bushing

@).

- Take off support ring 41).

- Take off seal ring

48.

- Take off lock ring@.

- Take off dust boot Cs).

- Unclamp the fork leg.

The operations are the same on both fork legs.

Preparatory work

- Disassemble the fork legs. (

�

p. 20)

Main work

- Pull the spring downward. Mount the open end wrench on

the hexagonal part.

- Clamp the open end wrench in the vise. Release screw

cap

but do not remove it yet.

I Mounting tool (T1404 7) (

p. 370)

- Pull the spring downward. Remove the open end wrench.

- Remove the screw cap.

- Remove the spring with the preload spacer(s).

Содержание F2203P4






























































































































































































































































































































































































Результаты поиска

Содержание F2203P4

Отзывы:

Похожие инструкции для F2203P4

Бренды по названию

Популярные бренды

Husqvarna F2203P4, Руководство по ремонту

Результаты поиска

Содержание F2203P4

Отзывы:

Похожие инструкции для F2203P4

Бренды по названию

Популярные бренды