Husqvarna F2203P4 Скачать руководство пользователя страница 95

Страница: 95 / 381

11.4

11.5

11 AIR FILTER

Installing the air filter

Main work

Mount the clean air filter on the air filter support.

Grease the air filter in area 6).

Long-life grease (

p. 354)

Insert both parts together, position them, and secure them

using air filter holder

in area

G,.

✓ The arrow of marking

faces up.

•

Info

If the air filter is not mounted correctly, dust and dirt

may enter the engine and result in damage.

Finishing work

Install the air filter box cover. (

p. 92)

Cleanin the air filter and air filter box

Warning

Environmental hazard

Hazardous substances cause environmental damage.

Dispose of oils, grease, filters, fuel, cleaning agents, brake fluid, etc., correctly and in compliance

with the applicable regulations.

Info

Do not clean the air filter with fuel or petroleum since these substances attack the foam.

M00303-01

Preparatory work

Remove the air filter box cover. (

p. 92)

Remove the air filter. (

p. 92)

Main work

Wash the air filter thoroughly in special cleaning liquid and
allow it to dry properly.

Air filter cleaning agent (

�

p. 354)

•

Info

Only press the air filter to dry it, never wring it out.

Oil the dry air filter with a high quality filter oil.

Oil for foam air filter (

I!!,!

p. 355)

Clean the air filter box.

Check the intake flange for damage and looseness.

Содержание F2203P4






























































































































































































































































































































































































Результаты поиска

Содержание F2203P4

Отзывы:

Похожие инструкции для F2203P4

Бренды по названию

Популярные бренды

Husqvarna F2203P4, Руководство по ремонту

Результаты поиска

Содержание F2203P4

Отзывы:

Похожие инструкции для F2203P4

Бренды по названию

Популярные бренды