Husqvarna 2013 TC 250R Скачать руководство пользователя

Страница: 42 / 351

D.12

TE 250R - 310R 2013 I.E. / TE 310R 2013 I.E. USA

TC 250R 2013 - TC 250R 2013 I.E. USA

TXC 250R - 310R 2013 I.E. USA

H09070

H09071

H11279

SETTINGS AND ADJUSTMENTS

Workshop Manual Ed. 07-2012

A: to increase clearance

B: to decrease clearance

Front brake lever adjustment and fluid level check

The adjuster (1) located on the control lever, allows adjusting of the free play

(a). Free play (a) must be at least 0,39 in. (10 mm).

The level of the fluid in master cylinder reservoir must never be below the mini

mum value (2), which can be checked from the inspection window on the rear of

the master cylinder body. A decrease of the fluid level will let air into the system,

hence an extension of the lever stroke.

If the brake lever feels mushy when pulled, there may be air in the

brake line or the brake may be defective: CHECK THE BRAKING
SYSTEM (see Section "L").

Too much brake lever free play may reduce braking action: CHECK

BRAKE PAD THICKNESS (see Section "L").

Do not spill brake fluid onto any painted surface or lens (for example

lights lens).

Do not mix two brands of fluid. Completely change the brake fluid

in the brake system if you wish to switch to another fluid brand.

Brake fluid may cause irritation. Avoid contact with skin or eyes.

In case of contact, flush thoroughly with water and call a doctor if

your eyes were exposed.

Содержание 2013 TC 250R
































































































































































































































































































































































Результаты поиска

Содержание 2013 TC 250R

Отзывы:

Похожие инструкции для 2013 TC 250R

Бренды по названию

Популярные бренды

Husqvarna 2013 TC 250R, Руководство по ремонту

Результаты поиска

Содержание 2013 TC 250R

Отзывы:

Похожие инструкции для 2013 TC 250R

Бренды по названию

Популярные бренды