Husqvarna 2013 TC 250R Скачать руководство пользователя страница 344

Страница: 344 / 351

Y.7

TE 250R - 310R 2013 I.E. / TE 310R 2013 I.E. USA

TC 250R 2013 - TC 250R 2013 I.E. USA

TXC 250R - 310R 2013 I.E. USA

H10170

H10171

H02632

CHASSIS AND WHEELS

Workshop Manual Ed. 07-2012

Reassembling the front wheel

Fit the L.H. spacer (1) on the wheel hub.

Fit the wheel between the fork legs so as to set the brake disc into the calliper.

Fit the wheel axle (2) from the R.H. side, after greasing it and push it fully

home against the L.H. fork leg; during this operation, the wheel should be

turned.

Tighten the screw (3) on the fork L.H. side but DO NOT lock it. Now, pump for a

while, pushing the handlebar downwards until you are sure that the fork legs are

perfectly aligned. Lock: the screws (4) on the R.H. leg (10.4 Nm, 1.05 Kgm, 7.7

ft/lb), the screw (3) on the L.H. side (51.45 Nm, 5.25 Kgm, 38 ft/lb), the screws

(1) on the L.H. leg ( 10.4 Nm, 1.05 Kgm, 7.7 ft-lb).

After reassembly, pull the brake control lever until the pads are

against the brake disc.

Speed sensor (TE)

Check the gap “B” between magnet (6) on brake disc and sensor (7) on brake

calliper.

Содержание 2013 TC 250R
































































































































































































































































































































































Результаты поиска

Содержание 2013 TC 250R

Отзывы:

Бренды по названию

Популярные бренды

Husqvarna 2013 TC 250R, Руководство по ремонту

Результаты поиска

Содержание 2013 TC 250R

Отзывы:

Бренды по названию

Популярные бренды