Husqvarna 2013 TC 250R Скачать руководство пользователя

Страница: 308 / 351

N.3

TE 250R - 310R 2013 I.E. / TE 310R 2013 I.E. USA

TC 250R 2013 - TC 250R 2013 I.E. USA

TXC 250R - 310R 2013 I.E. USA

H10153

ENGINE COOLING

Workshop Manual Ed. 07-2012

Coolant level check

Coolant takes the heat from the piston-cylinder-and-head assembly and transfers

it to the radiator, where it is released to the atmosphere. Checking coolant level

at regular periods is critical to ensuring proper operation of the cooling system.

Without cooling medium (water), no heat exchange occurs between

cylinder head and radiator. The cylinder and piston assembly will

overheat and seize and in the worst scenario, crankshaft damage

may result.

If the event of engine overheating, check that the radiator is full.

Level in the radiator must be checked from cold (see Section D).

In the event you need to check level when the engine is hot, be sure to discharge

pressure gradually.

The radiator cap (1) has a pressure-relief position to depressurize the system safely.

Failure to follow the above instructions will create a risk of scalding

for operator and any persons standing nearby.

A. Coolant level

B. Breather hose

Содержание 2013 TC 250R
































































































































































































































































































































































Результаты поиска

Содержание 2013 TC 250R

Отзывы:

Похожие инструкции для 2013 TC 250R

Бренды по названию

Популярные бренды

Husqvarna 2013 TC 250R, Руководство по ремонту

Результаты поиска

Содержание 2013 TC 250R

Отзывы:

Похожие инструкции для 2013 TC 250R

Бренды по названию

Популярные бренды