Husqvarna 2013 TC 250R страница 227 Скачать руководство пользователя

Страница: 227 / 351

I.23

TE 250R - 310R 2013 I.E. / TE 310R 2013 I.E. USA

TC 250R 2013 - TC 250R 2013 I.E. USA

TXC 250R - 310R 2013 I.E. USA

H06881

H06878

H06879

H06880

FRONT SUSPENSION

Workshop Manual Ed. 07-2012

Check the spring.

Replace it if:

outside diameter is damaged or exceedingly worn.

Free length is 457 mm (18 in.) or less.

Check the inner tube.

Replace if distorted.

(Never attempt to repair or reuse a distorted fork tube).

If the tube shows surface defects, sand the surface.

If repair is not possible, replace the tube.

(Never reuse an inner tube if scored or showing bulges on the outer surface).

Check the outer tube.

Replace the tube is any distortion is detected or if the sliding surface is damaged.

Mount sealing rings and metal parts on the inner tube.

See the figure below for the installation sequence.

Note 1: Grease the edge of the sealing ring.

Note 2: Before sliding the sealing ring over the inner tube, cover tube edge with

plastic as shown in the figure.

This will avoid damage to the oil seal lip.

Содержание 2013 TC 250R
































































































































































































































































































































































Результаты поиска

Содержание 2013 TC 250R

Отзывы:

Похожие инструкции для 2013 TC 250R

Бренды по названию

Популярные бренды

Husqvarna 2013 TC 250R, Руководство по ремонту

Результаты поиска

Содержание 2013 TC 250R

Отзывы:

Похожие инструкции для 2013 TC 250R

Бренды по названию

Популярные бренды