background image

13

humantouch.com

12

Operating Voltage: 

AC110-120V 60 Hz  

Power Consumption: 

65 Watts

Chair Size (upright):  

31” L x 30” W x 42” H 

Chair Size (reclined):  

50” L x 30” W x 35” H 

Required Recline Clearance:  20”
Product Weight:  

89 Lbs.

Maximum Load Weight:  

285 Lbs.

*Specifications are subject to change without prior notice.

Specifications*

Warranty

For warranty information, please contact your distributor.

WARNING:

 

This product is equipped with a thermal resetting protection device. This is an added safety feature 

to protect you and this product from overheating. If the product should suddenly stop and will not start, turn the 
main power switch, located on the back of the product, to off and do not operate the product for at least 30 minutes. 
Failure to turn the product off may result in the product starting unexpectedly when the product cools.

To keep your product working and looking its best, please follow 
these simple care guidelines.

care and

 maintenance

WARNING:

 

1.  Be sure to disconnect the power cord from the electrical outlet before cleaning.
2.  When cleaning the controller or power switch, use a dry cloth only. Never use a damp cloth to clean the controller  
  or power switch.
3.  Be sure to test any cleaning solution on a small, inconspicuous part of the product to ensure that the color does 
  not fade prior to using the solution on the entire product surface.

4.  Do not use benzene, thinner or any other solvents on your product.

Cleaning Code Standard: W

To maintain your Human Touch product in optimum condition, dust it frequently and/or vacuum it with a soft brush vacuum 

extension. SofSuede

®

 products can also be brushed with a suede brush. If your product becomes dirty, use a water-based 

upholstery cleaner only. To treat stains, spot clean with an upholstery shampoo or a mild detergent foam.

Maintenance and Repair:

1.  The mechanics of this product are specially designed and constructed to be maintenance free. No periodic lubrication  
  or servicing is required.
2.  Your chair should only be serviced by an authorized service center.

Use and Storage Environment:

1.  When not in use for a long period of time, we recommend that the chair be covered, the power cord be coiled and that  
  the unit be placed in an environment free of dust and moisture.

2.  Do not store near heat or open flame. 
3.  Do not leave this product exposed to direct sunlight for long periods of time. This may cause fading or damage.
4.  Do not use or store in extreme temperatures; product stored in cold temperatures may require 48 hours at room 

 

  temperature to function properly.

5.  Product should be used and stored in an environment with non-condensing humidity ranging from 10 to 80%; 

 

  excessive humidity will damage the mechanics.

Miscellaneous:

1. Foreign objects should not be inserted between the massage nodes or the unit housing.
2. Care should be taken not to overload the unit. 

Содержание feel better HT-044PS




































Отзывы: