Huawei NetCol5000-C030 Series Скачать руководство пользователя страница 139

Страница: 139 / 215

No. Operation

Troubleshooting

Period

Result

Check whether the

display panel,

humidity and

temperature sensor

or cables is aging on

the surface.

Replace the components or

cables.

Semi-

annual

□Passed
□Failed

Use a high-precision

humidity and

temperature sensor

to calibrate the

humidity and

temperature sensors

inside and outside

the cabinet.

If the temperature deviation

is greater than 1°C or

humidity deviation is greater

than 5%, calibrate or replace

the humidity and

temperature sensor.

Semi-

annual

□Passed
□Failed

The heat exchanger

fins are not pushed

down.

Use a fin brush to organize

the fins that are pushed

down.

Semi-

annual

□Passed
□Failed

Check that the

thermal insulation

foam on the chilled

water pipe is intact.

Rewrap the thermal

insulation foam.

Semi-

annual

□Passed
□Failed

Check that the pipe

support is intact and

securely installed.

Secure the base.

Semi-

annual

□Passed
□Failed

Check that pipes do

not leak.

Close the water inlet stop

valve and repair leaks.

Semi-

annual

□Passed
□Failed

Check that the smart

cooling product

drainpipe is free from

leaks and blockages.

If the drainpipe leaks, repair

the leaks. If the drainpipe is

blocked, clear the blockage

inside the pipe.

Semi-

annual

□Passed
□Failed

NetCol5000-C(030, 032, 065) In-row Chilled Water

Smart Cooling Product

User Manual

6 System Operation and Maintenance

Issue 04 (2021-03-15)

131

Содержание NetCol5000-C030 Series
























































































































































































































Результаты поиска

Содержание NetCol5000-C030 Series

Отзывы:

Похожие инструкции для NetCol5000-C030 Series

Бренды по названию

Популярные бренды

Huawei NetCol5000-C030 Series, Руководство пользователя

Результаты поиска

Содержание NetCol5000-C030 Series

Отзывы:

Похожие инструкции для NetCol5000-C030 Series

Бренды по названию

Популярные бренды