Huawei NetCol5000-C030 Series Скачать руководство пользователя страница 108

Страница: 108 / 215

Paramete

Description

Setting Rule

Default

Value

Requireme

nt control

Enable or disable the

requirement control for the

master device.
● When the requirement

control is Disable, the

master device does not

synchronize data to the

slave device, and all the

smart cooling products

operate based on their

own requirements, not

referring to the mode

delivered by the master

device.

● When the requirement

control is Anti-

competitive running,

the master device

synchronizes data (the

temperature and

humidity control type

and set points of the

master device and other

parameters) to the slave

device, and all the smart

cooling products in the

group refer to the mode

delivered by the master

device.

● When the requirement

control is Indoor fan

unified control or

Central load

distribution, all smart

cooling product fans in

the group rotate at the

same speed.

Anti-competitive

running is

recommended for the

following scenario: In

one teamwork, the

temperature and

humidity control type

and temperature and

humidity set point of

units are the same,

and device heat loads

are distributed evenly.

Disable

Cascade

function

After the requirement

control is enabled, you can

configure Cascade

function. The cascade

function starts standby

smart cooling products if

the active one cannot meet

the refrigerating

requirements.

If the heat load to the

device increases, the

cascade function is

recommended.

Disable

NetCol5000-C(030, 032, 065) In-row Chilled Water

Smart Cooling Product

User Manual

4 Power-On Commissioning

Issue 04 (2021-03-15)

100

Содержание NetCol5000-C030 Series
























































































































































































































Результаты поиска

Содержание NetCol5000-C030 Series

Отзывы:

Похожие инструкции для NetCol5000-C030 Series

Бренды по названию

Популярные бренды

Huawei NetCol5000-C030 Series, Руководство пользователя

Результаты поиска

Содержание NetCol5000-C030 Series

Отзывы:

Похожие инструкции для NetCol5000-C030 Series

Бренды по названию

Популярные бренды